vacuubrand PC 3001 TE VARIO PRO Instructions For Use Manual Download Page 110

Page: 110 / 121

page 110 of 121

➨

Tighten the union nut (K) of the hose con-

nection with an open-ended wrench w/f 17.

Tighten the union nut first by hand and then

tighten one full turn using the open ended

wrench.

PC 3001 VARIO

pro

/ PC 3001 VARIO

pro

Assemble the exhaust vapor condenser.

➨

Feed the PTFE hose from the pump outlet

into the inlet of the exhaust vapor condens-

er.

➨

Mount the condenser with the counter hold-

er (Torx screws T10) to the pump.

➨

Fasten union nut.

PC 3001 VARIO

pro

Assemble the inlet condenser.

➨

Slip the hose from the inlet of the pump onto

the hose connector of the inlet condenser.

➨

Mount the condenser with the counter hold-

er (Torx screws T10) to the pump.

➨

Tighten the union nut first by hand and then

tighten one full turn using the open ended

wrench.

PC 3001 VARIO

pro

Assemble the emission condenser TE.

➨

Feed the PTFE hose from the pump outlet

into the inlet of the emission condenser TE.

➨

Attach the mounting plate of the emission

condenser TE with 2 screws at the hous-

ing cover of the pumping unit; use a Phil-

lips screw driver size 2. Pay attention to the

cage nuts in the groove of the housing cov-

er.

➨

Fasten union nut.

Summary of Contents for PC 3001 TE VARIO PRO


























































































































Search results

Summary of Contents for PC 3001 TE VARIO PRO

Reviews:

Related manuals for PC 3001 TE VARIO PRO

Brands by name

Popular brands

vacuubrand PC 3001 TE VARIO PRO, Instructions For Use Manual

Search results

Summary of Contents for PC 3001 TE VARIO PRO

Reviews:

Related manuals for PC 3001 TE VARIO PRO

Brands by name

Popular brands