background image

8

Water System Operation

and Maintenance Manual

Procedure to Air  Purge the Water  System

Serial Numbers up to 0292655

1. Drain all water from water tanks.
2. Remove nozzle from sewer hose.
3. Start auxiliary engine.
4. Start truck chassis engine.
5. Turn top sewer hose control valve and bottom pump control valve on the front hose reel to the 

ON

position.

6. Turn air purge valve on left side of the water pump to the 

OPEN

 position.

7. Allow air to push water from hose.
8. When hose is free of water, rotate hose reel clockwise until all water is drained out.
9.

CLOSE

 air purge valve and turn 

OFF

 bottom water pump control valve and top sewer hose control

valve.

10. Remove handgun and plug from the handgun connection.
11. Turn 

ON

 handgun valve.

12. Turn 

ON

 bottom pump control valve.

13.

OPEN

 air purge valve and wait for all water to be blown from handgun system.

14. Turn 

OFF

 bottom pump control valve.

15. Tune 

OFF

 handgun valve.

16.

CLOSE

 air purge valve.

17.

OPEN

 debris body flushout valve.

18. Turn 

ON 

bottom pump control valve.

19.

OPEN

 air purge valve and wait for all water to be blown from water system hoses.

20. Turn 

OFF

 bottom pump control valve.

21.

CLOSE

 debris body flushout valve.

22.

CLOSE

 air purge valve.

23.

OPEN

 drain valves at water pump.

24.

OPEN

 air purge valve and wait for all water to be blown out of pump.

25.

CLOSE

 air purge valve.

26. Shut 

OFF

 auxiliary engine.

27. Shut 

OFF

 truck chassis engine.

28. Remove drain caps from water system bulkhead fittings under bumper, curb side.
29. NOTE:  Store unit with all  the water system ball valves in the 

ON

 position.

CAUTION:  Water freezes at 32 degrees F.  If at all possible try to store unit in an area above this

    temperature.

IF ABOVE PROCEDURE IS FOLLOWED, UNIT SHOULD BE FREE OF WATER.

Summary of Contents for 691-7001

















Reviews: