background image

Installation instructions

Heat pump dryer
Multi-family building

J173.113-0

6.4.11  ITH

5

Washer-dryer tower

Refer to the identification plate for specifications for the required mains voltage, current type and fuses.

Application height of the appliance: up to max. 2000 m above sea level

3. Connecting the condensate drain

When installing the drain hose, protect it against damage and bending!

To ensure proper drainage, do not extend the drain hose.

Install plastic hose supplied (length 
2,0 m, ø internal 10 mm) on drain 
connection of the appliance and 
secure using clamp supplied.

Feed plastic hose in sink drain trap or 
drain hose.

Electrical connections

Electrical connections must made by trained electricians in accordance with the guidelines and standards for low voltage 
installations and the specifications of the local electricity supply companies.
A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. An 
all-pole mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug and 
socket devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles switching 
are permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors ensure safe and 
fault-free operation. After installation, live parts and cables with basic insulation must not be accessible. Old installations should 
always be checked.

Connection cable

Error message «U1»

Colour code

400 V 3N~ 50 Hz, 10 A

Disconnect the appliance from the 
mains and control the connections.

L3
L2
L1

grey
black
brown
blue
yellow/green

E42

: Check the neutral conductor!

E43

: Check the pole conductors L2 and L3!

max. 1200 min. 800

min. 250

Drain into fixed

upright outflow pipe

Connection to

sink drain trap

Set W5.3070

max. 700

N

L3
L2
L1

5 × 1 mm

2

N

Summary of Contents for 173







Reviews: