manualshive.com logo in svg

V-TAC VT-5129, Installation Instructions Manual

Share
Download
V-TAC VT-5129 Installation Instructions Manual Download Page 9

CODE LEARNING/PAIRING OR DELETE

I FIRST PAIRING

II ADD MORE KEYS

III DELETE KEYS

-> Keep pressing the receiver key for 2s 
-> LED light is flashing, loosen receiver key and enter the learning mode. 
-> Press the remote key which you want to learn code.
-> Lamp turns on. Pairing is successful.

-> Press and hold paired remote key for about 20s �ll LED inidcator on switch blinks rapidly, 
then loosen your grip, press the new once. Finally test whether it can turn on/off the lamps.

-> Press and hold paired remote key for about 60s, during remote LED indicator on remote 
changes from:
Firstly blinks rapidly; Secondly blinks 8 �mes slowly, Thirdly blinks 9 �mes at slower speed, 
Finally blinks once at slowest speed, then loosen your grip, press the remote key again to check 
if you the keys have been deleted or not.

 

 

IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT: [email protected]

FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST 

DEALERS. V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B

Summary of Contents for VT-5129










Reviews:

No comments

Brands by name

Popular brands

Load more brands