background image

Safety

Storage and Use

Your product is intended for use in clean dry conditions. You
should avoid storage in excessively cold or damp places as this may
lead to corrosion and other related problems that are outside our
control.

Weight Limit

Your product is suitable for users weighing:
264 LBS / 18.8 Stones / 120 KG or less. 

Conformity

This product conforms to:

- HOME USE - Class (HC).

It is NOT suitable for therapeutic purposes.  

If any part of your product 
becomes damaged, broken 
or badly worn do not use 
the equipment until the 
defective parts have been 
replaced

Warning

BS EN ISO 20957-1 and BS EN 957-2 

Before you undertake any programme of exercise that will increase
cardiovascular activity please be sure to consult with your doctor.
Frequent strenuous exercise should be approved by your doctor and
proper use of your product is essential. Please read this manual
carefully before commencing assembly of your product or starting to
exercise.

* Please keep all children away from exercise products when in

use. Do not allow children to climb or play on them when they
are not in use.  

* For your own safety, always ensure that there is at least 1 Metre

of free space in all directions around your product while you are
exercising.  

* Regularly check to see that all nuts, bolts and fittings are

securely tightened. Periodically checking all moving parts for
obvious signs of wear or damage.  

* Clean only with a damp cloth, do not use solvent cleaners. If you

are in any doubt, do not use your product, but contact
CUSTOMER SUPPORT by any of the means listed on the
opposite page.   

* Before use, always ensure that your product is positioned on a 

solid, flat surface. If necessary, use a rubber mat underneath to

reduce the possibility of damaging flooring or slipping in use.

* Always wear appropriate clothing and footwear such as training

shoes when exercising. Do not wear loose clothing that could
become caught or trapped during exercise.  

Page 

Summary of Contents for STB-22/100





























Reviews: