manualshive.com logo in svg

UWT NivoRadar NR 7100 Series, Technical Information/Instruction Manual

Share
Download
UWT NivoRadar NR 7100 Series Technical Information/Instruction Manual Download Page 38

NivoRadar

®

Continuous level measurement

Series NR 7100

Technical information / Instruction manual

Diagnostics and servicing

page 38

Code
Text message

Cause

Rectification

C700
Simulation active

A simulation is active

Finish simulation
Wait for the automatic end after 60 mins.

Code
Text message

Cause

Rectification

S600
Impermissible electron-
ics temperature

Temperature of the electronics in the 
non-specified range

Check ambient temperature
Insulate electronics

S601
Overfilling

Danger of vessel overfilling

Make sure that there is no further filling
Check level in the vessel

S603
Impermissible operating 
voltage

Terminal voltage too small

Check terminal voltage, increase operat-
ing voltage

Code
Text message

Cause

Rectification

M500
Error in the delivery 
status

The data could not be restored during 
the reset to delivery status

Repeat reset
Load XML file with sensor data into the 
sensor

M501
Error in the delivery 
status

Hardware error EEPROM

Send instrument for repair

M507
Error in the instrument 

settings

Error during setup
Error when carrying out a reset
False signal suppression faulty

Carry out reset and repeat setup

M508
No executable 
Bluetooth software

Checksum error in Bluetooth software

Carry out software update

M509
Software update run-

ning

Software update running

Wait until software update is finished

M510
No communication with 
the main controller

Communication between main electron-
ics and display module disturbed

Check the connection cable to the dis-
play
Send instrument for repair

M511

Inconsistent software 
configuration

A software unit requires a software up-
date

Carry out software update

Function check

Out of specification

Maintenance

Summary of Contents for NivoRadar NR 7100 Series

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands