UWE APM Operation Manual Download Page 17 | Manualshive

Page: 17 / 17

background image

APPENDIX: ERROR CODES

P_OFF

Low battery status is detected during power on. Indicator

will shut off after this message appeared.

Error

Error during calibration.

Case 1:

The 1

st

calibration weight entered is less than 1/3 of

rated capacity

Case 2:

The 2

nd

calibration weight entered is over the

rated capacity.

Case 3: The span value is not within the acceptable range.

«
...
15
16
17

Summary of Contents for APM


















Reviews:

No comments

Related manuals for APM

Brand: Salter Housewares Pages: 25

Brand: Salter Pages: 16

Brand: inventum Pages: 11

Brand: Orbegozo Pages: 13

Brand: RADWAG Pages: 196

Brand: A&D Pages: 88

Brand: OHAUS Pages: 46

Poultry Production Systems WEIGH-MATIC

Brand: Chore-Time Pages: 18

Brand: Doran Pages: 23

Brand: Scarlett Pages: 12

Brand: marsden Pages: 12

Brand: Orbegozo Pages: 17

Brand: Johnson Pages: 16

TRACK & TARGET USTT180

Brand: Escali Pages: 4

Brand: Salter Pages: 8

Brand: Salter Pages: 12

Brand: Salter Pages: 24

Brand: Salter Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands