Utopia Lustre Installation Manual Download Page 3

Installation Guide  

Lustre Toilet Unit Without Cistern 

 

Important Information 

 

  Read the instructions carefully. 

  Check the product for any signs of damage and remove any protective film.  

  It is recommended that a technically competent installer undertakes installation.  

  It is the i

nstaller’s responsibility to carry out a thorough assessment of the wall type 

and the weight of the cabinet and use appropriate fixings.  

  Care should be taken when drilling walls to avoid any hidden wires or pipes. 

 
 

Installation 

 

To fit a concealed cistern into the WC unit, pull the front top  
fascia away from the cabinet. The lower front panel can now  
be lifted upwards away from the cabinet. Secure the cistern  
in position according to the instructions supplied with it.  

 

To secure the WC unit against the wall, screw the stretcher plates  
to the gable panels of the cabinet as shown in the diagram.  
Ensure that the screws used are suitable for the thickness of the  
cabinet. 
 
Mark the position of the holes in the stretcher plates on the wall  
with a pencil. Drill the positions marked with a suitable drill bit.  
 
Fasten the unit in position through the stretcher plates using  
fixings suitable for the wall type. 
 
To cut the lower fascia panel to accommodate the soil pipe and  
cistern flush pipe, use a jigsaw with a fine-toothed blade suitable  
for timber. Ensure that the room is well ventilated when cutting  
the material.  
 
All cut edges must be sealed with PVA glue or good-quality, sanitary  
grade silicone sealant to prevent the ingression of moisture. 

 
 

Care & Maintenance

 

Furniture should be regularly dusted with a soft cotton or micro-fibre  
cloth. For more thorough cleaning, occasionally wipe your furniture  
with a soft cloth dampened with a mild detergent solution. Surfaces  
should be thoroughly dried with a lint free cloth to prevent watermarks.  
Under no circumstances should solvent cleaning agents, bleach or  
abrasive cleaning agents or cloths be used. Spills should be removed  
immediately using a clean cloth. All bathroom furniture will deteriorate  
through prolonged periods of exposure to high levels of condensation  
so bathrooms must be adequately ventilated using suitable extraction.  
Failure to ensure adequate ventilation may invalidate your guarantee.  

 

Summary of Contents for Lustre













Reviews: