Utopia Lustre Installation Manual Download Page 10

 
 
Fitting Cabinet to Wall 

It may be necessary to snap the wall plate in half at the marked line  
to create two wall brackets. Mark a horizontal line on the wall at the  
required height X---X. Ensure that the wall brackets will fit inside the  
width of the cabinet and are equally spaced to ensure even distribution  
of weight. Secure the wall brackets to the wall using suitable fixings

 
Hook the unit onto the wall brackets ensuring that the brackets are securely  
located. 
 
To alter the position of the cabinet on the wall, adjust the two screws in each  
hanging bracket. The top screws will move the cabinet closer to or further away  
from the wall. The lower screws will move the cabinet up and down. 
 
A securing screw should be fitted through the back of the unit through the fixed  
back of the cabinet and into the wall, this will help to stabilise the unit. 
 

 

Door hinge adjustment 

 

To square the door against the cabinet, turn screws A until  
adjusted as required. 

 

To adjust the door closer to or further away from the cabinet,  
turn screws B. 

 

To adjust the door vertically, slacken screws C. Re-tighten  
once the door is adjusted as required. 

 

To remove the door hinges from the cabinet, press button D. 

 

To remove the door hinges from the door, remove screws E. 

 

 

 

 
Care & Maintenance 

Furniture should be regularly dusted with a soft cotton or micro-fibre cloth. For more thorough 
cleaning, occasionally wipe your furniture with a soft cloth dampened with a mild detergent 
solution. Surfaces should be thoroughly dried with a lint free cloth to prevent watermarks. Under 
no circumstances should solvent cleaning agents, bleach or abrasive cleaning agents or cloths be 
used. Glass or mirrored panels should be cleaned using a non-solvent based glass cleaner and a 
soft cloth. Spills should be removed immediately using a clean cloth. All bathroom furniture will 
deteriorate through prolonged periods of exposure to high levels of condensation so bathrooms 
must be adequately ventilated using suitable extraction. Failure to ensure adequate ventilation 
may invalidate your guarantee.  
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Summary of Contents for Lustre













Reviews: