UTILIS TMS 18 Assembly Instructions Manual Download Page 11 | Manualshive

Page: 11 / 21

background image

UTILIS S.A.S ZAC Eurotransit RUE ABBE MARIOTTE 57365 ENNERY FRANCE

T: +33 (0)3 87 71 60 74 W: www.utilis-international.com Email: [email protected]

11

11

Take the ground sheet green straps and then pull them till the
frame feet.

Lift the foot and pass the green strap under and
around it.

Locate the black bungee which is
attached near the green strap.
Place it around the axle.

Grab the eave rope and pass it through the
ring located on the frame corners.

Once you have finished this process on the 4 feet, do the same on
the other side feet.
The tent is now in this configuration.

«
...
9
10
11
12
13
...
»

Summary of Contents for TMS 18






















Reviews:

No comments

Related manuals for TMS 18

Copper Canyon 1610

Brand: Eureka Pages: 2

Brand: DARCHE Pages: 8

YELLOWSTONE VENT II

Brand: Jack Wolfskin Pages: 8

Brand: ABSCO SHEDS Pages: 60

Brand: NRS Relief Pages: 2

Brand: Global Pages: 4

Brand: EPS Pages: 16

Brand: Ozark Trail Pages: 4

Brand: Vango Pages: 3

Pagoda Marquee UNICO 7x7m

Brand: Dancover Pages: 7

Brand: Vango Pages: 3

Brand: BALCO Pages: 13

Brand: Quest Engineering Pages: 12

Brand: Sojag Pages: 112

Brand: Savotta Pages: 4

Brand: Serco Pages: 4

Giant Pro PVC 5m Series

Brand: Stabilezelte Pages: 20

GIANT PROFESSIONAL PVC

Brand: Stabilezelte Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands