ABSCO SHEDS 3052UTK Assembly & Instruction Manual Download Page 1

Page: 1 / 60

Absco Industries

Assembly Instruction Manual

ABSCO UTILITY SHED

MODEL: 3052UTK

3.00mW x 5.22mD x 2.10mH

Model: 3052UTK

09/07/2019

1.12

Download the Absco
Sheds Assembly App
for instructional videos

MANU FA CT URED

IN A US TR ALIA

SNAPTiTE

Assemb ly

AU: 1800 029 701

N Z: 0800 466 444

[email protected]

www.abscosheds.com.au

CONCRETE SLA

5320mm

3100m

When laying concrete slab, ensure there
is a rebated edge 25mm deep around
the perimeter. This will help water egress
from the base of the shed.

For construction in non-cyclonic areas

Wind rating: N2 as per AS4055-2012.
If you require a higher wind rating please contact
us: [email protected] or 1800 029 701

ABSCO INDUSTRIES

ASSEMBLY INSTRUCTION MANUAL

SHED MODEL: 23151GK

21-11-2017

CONCRETE SLAB

2360mm

1620mm

FRONT: 2.26m

SIDE: 1.52m

HEIGHT: 1.95m

We thank you for choosing an Australian made

shed. For further assistance please visit our detailed

instructional video library at

Http://www.abscosheds.com.au/watch-videos

At ABSCO Industries we are always looking to be

number ONE, so please let us know what you think

of our instructions. Feedback makes us better.

[email protected]

CONCRETE

REBATED EDGE

BOTTOM CHANNEL

CONCRETE SLAB

75mm WIDE REBATE

100mm

WHEN LAYING YOUR CONCRETE

SLAB, ENSURE THERE IS A

REBATED EDGE 25mm DEEP

AROUND THE PERIMETER

THIS WILL HELP WATER EGRESS

FROM THE BASE OF THE SHED

Absco Industries

Premier Shed Model: 23151GK

PAGE 01

Summary of Contents for 3052UTK





























































Search results

Summary of Contents for 3052UTK

Reviews:

Related manuals for 3052UTK

Brands by name

Popular brands

ABSCO SHEDS 3052UTK, Assembly & Instruction Manual

Search results

Summary of Contents for 3052UTK

Reviews:

Related manuals for 3052UTK

Brands by name

Popular brands