UTICA BOILERS MACF-115 Manual Download

Page: 51 / 139

FIGURE 9-1 Condensate Drain Assembly

150 Model shown (location similar in all sizes)

9.4 Fill Condensate Trap with Water

WARNING

Asphyxiation hazard! Fill condensate trap

before starting boiler to avoid combustion

products escaping boiler. Failure to follow these

instructions could result in death or serious

injury.

•

To fill the condensate trap pour water into exhaust

vent until water begins to flow through the siphon.

• Visually inspect the siphon to ensure it is full with

clean water.

• During operation check condensate trap to ensure it

drains properly.

Note

Condensate trap must be manually filled with

water at initial start up.

•

Boiler is fitted with automatic air vent positioned on

pump Vent and is fitted with adjustable sealing cap.

See Figure 9-1.

•

Open central heating flow and return valves. Spindle

is flat in-line with valve.

•

Open fill point valve on filling system until water

begins to flow. To aid venting boiler drain may be

open until water flows out. Close drain as soon as

water appears.

• During initial system air purge open valve connected

to top left of heat exchanger. Open four (4) full

turns counterclockwise until steady stream of water

is witnessed. Close fully turning clockwise with no

tools needed. See Figure 9-1.

• Systems using radiators to remove air - Vent each

radiator in turn, starting with lowest in the system.

• It is

IMPORTANT

the pump is properly vented

to avoid running it dry and damaging its bearings.

Unscrew and remove cap from center of pump. Use

screwdriver. Rotate exposed spindle about half turn,

replace cap.

• Check operation of heating pressure relief valve. Pull

lever on top of valve upwards lifting the seat. This

will allow water to escape from system. Check water

is escaping from the system.

• Open cold water supply inlet valve. Turn on all

domestic hot water taps. Allow water to flow until no

air is present. Turn off domestic hot water taps. See

page 4 - Physical Data and section 2.7 Operational

Features.

9.3 System Start Up

Follow all codes and regulations when filling the boiler.

Use drain taps to allow system to completely drain.

Thoroughly flush the heating system before boiler is

connected and again after first heating season.

9 - START UP PROCEDURE

240013371 REV B, [10/01/2021]

Condensate Drain

Connection

Pour

approximately

1 cup of water

into flue way

of boiler.

Air

Purge

Valve

Condensate

Tray

Air Vent

Summary of Contents for MACF-115












































































































































Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands

UTICA BOILERS MACF-115, Manual

Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands