UTICA BOILERS MACF-115 Manual Download

Page: 37 / 139

YES

FIGURE 6-3 - Low Water Cutoff - Detail

6.6 External Optional Low Water Cut Off

These guidelines are supplied when necessary to install

an additional Low Water Cut Off (LWCO), for sensing a

low water level condition in a boiler, as required by the

Authority Having Jurisdiction.

Follow LWCO manufacturer installation instructions for

type of LWCO selected in addition to these instructions.

LWCO shall be 120V/60HZ control and dry contacts

sized for load being connected. Wire control to boiler.

See Figure 6-3.

Connect LWCO device to the system ground. Ground

in accordance with the requirements of the authority

having jurisdiction or, in the absence of such

requirements, with the National Electrical Code (NEC) or

Canadian Electrical Code CEC.

• Locate LWCO sensing device in the supply

piping, above the minimum height of boiler.

See Figure 6-2, Piping Diagram.

• Position control in HORIZONTAL piping to assure

proper boiler protection (upright or 90° rotation).

• For proper operation, sensing element of the LWCO

control shall be positioned in the tee to sense the

main water stream. Maintain minimum 1/4” spacing

from pipe walls. Element shall NOT contact the rear,

or side walls of the tee. See Figure 6-3.

• Install an air vent using a tee to avoid nuisance

shutdowns.

• Apply small amount of pipe sealant to threaded

connections. Use LWCO manufacturer suggested

sealant.

• Arrange piping to prevent water dripping onto boiler.
•

DO NOT install water shutoff valve between boiler

and LWCO sensing device.

Low Water Cutoff (LWCO)

Electrical Conduit

J-Box

120 V/60 HZ

Conduit or Power

Supply cord

(Polarized)

GND

BLK

WHT

120 V/60 HZ Socket

(Polarized) 120 V/60 HZ

Cord Set From Boiler

N.O

FIGURE 6-4 - LWCO Wiring Diagram

6 - HYDRONIC PIPING

240013371 REV B, [10/01/2021]

Summary of Contents for MACF-115












































































































































Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands

UTICA BOILERS MACF-115, Manual

Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands