UTICA BOILERS MACF-115 Manual Download

Page: 12 / 139

2 - INTRODUCTION

Check our website frequently for updates: www.ecrinternational.com

Information and specifications outlined in this manual in effect at the

time of printing of this manual. ECR International reserves the right to

discontinue, change specifications or system design at any time without

notice and without incurring any obligation, whatsoever.

2.5 Designated Use

• MACF-115

MACF-150

and

MACF-205

provide

both central heating and domestic hot water.

• MAHF-100, MAHF-125

and

MAHF-165

central

heating only.

• Indoor installation.
• Closet or alcove installation. Direct Vent Boiler

does not require air vents when installed in closet

or room.

• Direct vent boiler.
•

For use with natural gas or liquefied petroleum

gases (LP/propane).

2 - INTRODUCTION

2.1

Installation shall conform to requirements of

authority having jurisdiction or in absence of such

requirements:

UNITED STATES

• National Fuel Gas Code, ANSI Z223.1/NFPA 54

• National Electrical Code, NFPA 70.

2. 2

Where required by authority having jurisdiction,

installation shall conform to Standard for Controls and

Safety Devices for Automatically Fired Boilers, ANSI/

ASME CSD-1.

Additional manual reset low water cutoff may be

required.

2.3 Requirements for Commonwealth of

Massachusetts:

Boiler installation must conform to Commonwealth of

Massachusetts code 248 CMR which includes but is not

limited to:

Installation by licensed plumber or gas fitter.

2.6 The unit MUST NOT:

• Directly heat potable water. Indirect heating is

acceptable.

• Heat water with non-hydronic heating system

chemicals present (example, swimming pool

water).

• Toxic chemicals, such as those used for boiler

treatment, shall not be introduced into potable

water used for space heating.

• Exceed 43 psig (2.96 bar) maximum system

pressure, or drop below minimum system

pressure 7.25 psig (.50 bar)

• Exceed 176°F (80°C) system design temperature.

2.7 Operational Features

• MAHF-100

Modulates input to provide CH

Turndown 5.6:1

• MACF-115

Modulates input to provide CH

Turndown 5.6:1, DHW Turndown 6.9:1

• MAHF-125

Modulates input to provide CH

Turndown 5.7:1

• MACF-150

Modulates input to provide CH

Turndown 5.7:1, DHW Turndown 7:1

• MAHF-165

Modulates input to provide CH

Turndown 5.5:1

• MACF-205

Modulates input to provide CH

Turndown 5.5:1, DHW turndown 7:1

• Maximum output available for domestic hot

water:

MACF-115

- 105,500 btu/hr (33.8 kW) capable of

providing 2.5 (U.S.) gpm (11.4 liters/min) with a

temperature rise of 70°F/39°C.

MACF-150

- 136,000 btu/h (40 kW), capable of

providing 3.5 (U.S.) gpm (13.2 liters/min) with a

temperature rise of 70°F/39°C.

MACF-205

- 180,000 btu/h (53 kW), capable of

providing 5.0 (U.S.) gpm (18.9 liters/min) with

temperature rise of 70°F/39°C.

•

Integral Low Water Pressure Cutoff.

• Optional Outdoor Temperature Reset.
• Heat exchanger over heat protection.
• Boiler operating at maximum operating

temperature, providing heat, pressure gauge

should not indicate more than 26.11 psi /

1.80 bar. If reading exceeds this figure larger

expansion tank is required.

2.4 Manufacturer recommends use of Carbon

Monoxide monitor may be requirement of local

jurisdiction.

240013371 REV B, [10/01/2021]

Summary of Contents for MACF-115












































































































































Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands

UTICA BOILERS MACF-115, Manual

Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands