UTICA BOILERS MACF-115 Manual Download

Page: 11 / 139

1 - IMPORTANT INFORMATION

CAUTION

Indicates a hazardous situation which, if not

avoided, could result in minor or moderate injury.

WARNING

Indicates a hazardous situation which, if not

avoided, could result in death or serious injury.

DANGER

Indicates a hazardous situation which, if not

avoided, WILL result in death or serious injury.

This is the safety alert symbol. Symbol alerts you to

potential personal injury hazards. Obey all safety messages

following this symbol to avoid possible injury or death.

Become familiar with symbols identifying potential hazards.

Boiler installation shall be completed by qualified

agency. See glossary for additional information.

1. Safety Information

WARNING

Do not tamper with or use this boiler for any

purpose other than its intended use. Failure

to follow these instructions could result in

death or serious injury. Use only manufacturer

recommended parts and accessories.

CAUTION

Laceration, burn hazard. Metal edges and parts

may have sharp edges and/or may be hot. Use

appropriate personal protection equipment to

include safety glasses and gloves when installing

or servicing this boiler. Failure to follow these

instructions could result in minor or moderate

injury.

NOTICE

Used to address practices not related to personal

injury.

WARNING

Fire, explosion, asphyxiation and electrical shock

hazard. Improper installation could result in

death or serious injury. Read this manual and

understand all requirements before beginning

installation.

FOR YOUR SAFETY READ BEFORE OPERATING

Hot Water Can Scald

Water heated to temperature for clothes washing,

dish washing and other sanitizing needs can scald

and cause permanent injury.

Children, elderly, and infirmed or physically

handicapped persons are more likely to be

permanently injured by hot water. Never leave

them unattended in bathtub or shower. Never allow

small children to use a hot water tap or draw their

own bath.

If anyone using hot water in the building fits the

above description, or if state laws or local codes

require certain water temperatures at hot water

taps, you must take special precautions:

•

Use lowest possible temperature setting.

•

Install some type of tempering device, such

as an automatic mixing valve, at hot water tap

or water heater. Automatic mixing valve must be

selected and installed according to manufacturer's

recommendations and instructions.
•

Water passing out of drain valves may be

extremely hot. To avoid injury:

•

Make sure all connections are tight.

•

Direct water flow away from any person.

DANGER

Water

Temperature

Setting

1st Degree Burn

Exposure Time For

An Adult

2nd and 3rd Degree Burn

Exposure Time For An

Adult

120° F

1 minute

5 minutes

130° F

5 seconds

30 seconds

140° F

2 seconds

5 seconds

150° F

1 second

1.5 seconds

160° F

Instantaneous

0.5 seconds

Note:

Warning for Infants, Children, and Elderly:

Great care must be taken when exposing the

aforementioned groups to warm or hot water as they

can be badly burned in exposure times less than half

of the time for an adult.

WARNING

Fire, Explosion, Asphyxiation, Electrical shock

hazard! Flooding will result in damages such as

electrical problems, corrosion, inoperative parts,

mold and other unforeseen issues which can

occur over time. Any equipment determined by

a professional as damaged by a flood, defined as

excess of water or other liquid, shall be replaced.

Failure to follow these directions will result in a

Hazardous Situation.

240013371 REV B, [10/01/2021]

Summary of Contents for MACF-115












































































































































Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands

UTICA BOILERS MACF-115, Manual

Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands