manualshive.com logo in svg

UTE X2-1616, Manual, Page: 18 / 48

Share
Download
UTE X2-1616 Manual Download Page 18

X2-1616: Modular 16x16 Matrix Switcher

U.T.E. electronic GmbH & Co. KG

13 

www.ute.de

It also boasts embedded EDID management. 

X2-

4I-UH

: input card, maximum four input signal. Input signal can pass to output

device through X2-4O-UH, or other kinds of output cards.

Note:

 When matching with output cards that do not support 4kx2k, adjust the input 

resolution to 1080p to enable reliable output. 

X2-

4O-UH

: output card, maximum four output signal, output signals from X2-4I-UH,

or other kinds of input cards, HDCP compliant status settable via RS232 command 

The HDMI connector is same with X2-4I-HD& X2-4O-HD’s.

2.2.11. 

X2-

4I-UF & 

X2-

4O-UF

4K optical signal card. (Please check the specification from 5

.2.11

) 

Work with single-mode/ multi-mode module to realize long-distance optical fiber 

transmission, support multi-mode transmission up to 300m and single mode 

transmission up to 1km. 
High bandwidth: 10.2Gbps; Compliant with HDMI 1.4, capable to transmit 4K×2K& 

1080P 3D (max) signals;  

X2-

4I-UF

: input card with indicators, maximum four input signal, corresponding 

indicator illuminates green when there is input signal. Input signal can pass to 

output device through X2-4O-UF, or pass through other kinds of output cards.

X2-

4O-UF

: output card with indicators, maximum four output signal, output signals

from X2-4I-UF, or other kinds of input cards; corresponding indicator illuminates

green when there is output signal. 

Summary of Contents for X2-1616

















































Reviews:

No comments