Utax P-C2665 MFP User Manual Fax System Download | Manualshive

Page: 178 / 202

background image

Troubleshooting

8-6

Troubleshooting

When a problem occurs, first check the following. If the problem persists, contact your dealer or service
representative.

Symptom

Checkpoint

Corrective Action

Reference

Page

Cannot send document.

Is the modular cord
connected correctly?

Connect the modular cord
correctly.

–

Is

Communication error

displayed?

Remedy the cause of error
and send again.

Is TX (transmission)
restriction activated?

Cancel the TX restriction.

Cannot perform broadcast
transmission.

Is free space available in the
memory?

Check the job status, and if
there are unneeded jobs,
cancel the jobs to free memory,
or wait until transmission/
reception of jobs being printed /
jobs on standby is finished.

–

Cannot perform encrypted
communication.

Are the registrations correct
both at sender and recipient?

Double-check the
registrations both at sender
and recipient.

Cannot use the remote
switching function.

Is a pulse line used?

Some phones may transmit
tone signals using buttons.
Refer to the operation
manual of your phone set.

–

Is the remote switching
number correct?

Check the registration.
(Default: 55)

No print output after
reception.

I

s memory forwarding

activated?

Check the forwarding
destination.

–

Cannot receive document.

Is the modular cord
connected correctly?

Connect the modular cord
correctly.

–

Is

Communication error

displayed?

Remedy the cause of error
and ask the sender to retry.

Is RX (reception) restriction
activated?

Cancel the RX restriction.

Cannot perform memory
reception.

Is free space available in the
memory?

Check the job status, and if
there are unneeded jobs,
cancel the jobs to free memory,
or wait until transmission/
reception of jobs being printed /
jobs on standby is finished.

–

«
...
176
177
178
179
180
...
»

Summary of Contents for P-C2665 MFP











































































































































































































Reviews:

No comments

Related manuals for P-C2665 MFP

Brand: SA Pages: 5

Brand: Xante Pages: 25

Brand: LabelTac Pages: 15

Brand: Xerox Pages: 324

Brand: POS-TECHNOLOGY Pages: 40

Brand: Oce Pages: 330

Brand: Citizen Pages: 46

Brand: Magicard Pages: 124

Brand: Oki Pages: 83

THERMOMARK CARD

Brand: Phoenix Contact Pages: 35

Brand: Oki Pages: 138

Brand: Avery Dennison Pages: 92

Color ID Card Printer II

Brand: FARGO electronics Pages: 70

Brand: Canon Pages: 329

Brand: Canon Pages: 331

Brand: Canon Pages: 396

Brand: Canon Pages: 36

Brand: Canon Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands