background image

15

ITEM

DESCRIPTION

MODEL

PART#

11

Full Brick

BOTH

89066

12

Half Brick

1600

23887

13

Slide Baffle Plate

BOTH

24231

14

Grate Retainer

1600

40312(2)

1800

40337(2)

15

Baffle Rod S/S

1600

86603

1800

86607

16

Top Insulation

1600

C98871

1800

23979(2)

17

Front Filler

1600

23817

1800

24190

18

Draft Cover

1600

23818

1800

24508

19

Top Flue Ring

1600

22761

1800

23958

20

Draft Cap

BOTH

23859

21

1/2" x 2-1/2" Bolt

BOTH

C20599

22

Back Liner

1600

40313

1800

40339

23

Front Liner

1600

40344

1800

40338

24

Cabinet Side Back

1800

69002

ITEM

DESCRIPTION

MODEL

PART#

  1

Left Side Front Assy.

1600

68821

1800

68962

  2

Right Side Front Assy.

1600

68822

1800

68961

  3

Top Wrapper

1600

69088

1800

68964

  4

Back Weldment

1600

68823

1800

68963

  5

Side  Insulation  (2ea.)

1600

C98771

1800

23977

  6

Back  Insulation

1600

C98971

1800

23978(2)

  7

Ash Pan Weldment

1600

68882

1800

68919

  8

Carrying  Handle

1800

24233

  9

Shaker Grate Section

1600

23852

1800

23852

Shaker Grate Assembly

1600

68826

1800

68914

10

Shaker Bar

1600

891341

1800

891339

*

Snap in Receptacle

BOTH

80351

NOTE:

1600 = 16 - FULL BRICK
            3- HALF BRICK
1800 = 22 - FULL BRICK

2- HALF BRICK

PARTS LIST

MODEL 1600/1800

!! IMPORTANT !!

When ordering repair parts,

a "G" must be added to the

end of the part number of

any part painted GREEN on

the furnace.

24

Summary of Contents for 1600G

























Reviews: