Usr EV20i Owner'S Manual Download Page 18 | Manualshive

Page: 18 / 65

background image

16

AC CIRCUIT PROTECTOR

DC RECEPTACLE

DC CIRCUIT PROTECTOR

PUSH

AC CIRCUIT PROTECTOR

AC RECEPTACLES

AC CIRCUIT PROTECTOR

ON

OFF

ON

OFF

DC CIRCUIT PROTECTOR

DC RECEPTACLE

PUSH

The AC circuit protector will automatically switch OFF if there is a short
circuit or a significant overload of the generator at the AC receptacles.
If the circuit protector switches

OFF automatically, check that the

appliance is working properly and does not exceed the rated load
capacity of the circuit before resetting the circuit protector ON.

The DC circuit protector automatically shuts off the DC battery
charging circuit when the DC charging circuit is overloaded, when
there is a problem with the battery, or when the connections between
the battery and the generator are improper.

The DC receptacle should ONLY be used for charging 12-volt
automotive type batteries. The DC charging output is not regulated.

«
...
16
17
18
19
20
...
»

Summary of Contents for EV20i


































































Reviews:

No comments

Related manuals for EV20i

Brand: Powermate Pages: 12

Brand: Powerhorse Pages: 56

Brand: Hyundai Pages: 24

Brand: Consort Pages: 30

Brand: Wacker Neuson Pages: 42

Brand: Sangean Pages: 22

Brand: Thulos Pages: 5

Brand: Onan Pages: 108

Brand: Clarke Pages: 28

Brand: HP Pages: 53

Brand: HP Pages: 147

Intelligent Power Distribution Unit

Brand: HP Pages: 104

Brand: HP Pages: 114

Brand: HP Pages: 348

Brand: HP Pages: 445

Brand: HP Pages: 496

Brand: HP Pages: 1

SRS-RF930RK - Wireless Speaker Sys

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands