Usr EV20i Owner'S Manual Download Page 15 | Manualshive

Page: 15 / 65

background image

13

OUTPUT INDICATOR LIGHT

OVERLOAD INDICATOR LIGHT

OVERLOAD INDICATOR
LIGHT (RED)

OUTPUT INDICATOR
LIGHT (GREEN)

The output indicator light (green) is illuminated when the generator is
operating normally. It indicates that the generator is producing
electrical power at the receptacles.

If the generator is overloaded (in excess of 2,000 VA), or if there is a
short circuit in a connected appliance, the overload indicator light (red)
will go ON. The overload indicator light (red) will stay ON, and after
about four seconds, current to the connected appliance(s) will shut off,
and the output indicator light (green) will go OFF.

«
...
13
14
15
16
17
...
»

Summary of Contents for EV20i


































































Reviews:

No comments

Related manuals for EV20i

Brand: Magnavox Pages: 2

Brand: Baofeng Pages: 7

Brand: Tait Pages: 108

Brand: Accton Technology Pages: 2

Brand: VOLTCRAFT Pages: 50

Brand: Baofeng Pages: 34

Brand: Wacker Neuson Pages: 98

Brand: Hameg Pages: 28

Brand: Wacker Neuson Pages: 38

Brand: ELCOS Pages: 36

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 4

D2345 - annexe 1

Brand: Philips Pages: 4

Brand: Philips Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands