background image

- 13 -

CM-680

 I

NSTRUCTION 

M

ANUAL

 Ultra    Stereo Labs, Inc.

- 2 -

CM-680

 I

NSTRUCTION 

M

ANUAL

 Ultra    Stereo Labs, Inc.

Introduction .........................................................3

Front & Rear Panel Description............................5

Installation............................................................7

Crossover Setup...................................................11

Table of Contents

Please record the following information for your records:

Model: ___________________ Serial Number: ___________

Date of Purchase: __________ Purchased from: __________

Speaker     

 Crossover Frequency             Time Delay

JBL 4675D         

500Hz      

    

1.8ms.

JBL 4670           

800Hz                   

0.7ms,

JBL 5671           

330Hz                    

1.4ms

JBL 5672       

297Hz                    

1.8ms.

JBL 5674

297Hz

1.8ms

EV TS940           

800Hz                    

0.7ms.

EV TS992LX       

500HZ                   

1.8ms.

EV 9040               

500Hz                    

1.8ms

EV Variplex              

330Hz                    

1.4ms

EAW CB2591

500Hz

     

1.8ms

EAW CB259

800Hz

     

0.7ms

EAW CB253

350

     

0.7ms

1. Bypass Card XTB-680: 

When using external crossovers, the CM-680

must be equipped with a bypass card in the crossover slot. For connection

to a CP-650, slide dip switches D,E, & F on the XTB-680 to the “ON”

position. When using other electronic crossovers or speakers with passive

crossovers,  turn  DIP  switches  A,B  &  C  to  “ON”.  See  figure  #8

Connect crossover inputs to rear of CM-680 at Ll, Cl &Rl as per Fig.4

(Page9)

Figure 7

Summary of Contents for CM-680


















Reviews: