CAUTION:
PLEASE FOLLOW THIS INSTRUCTION MANUAL CAREFULLY TO
PREVENT ANY INJURIES OR COMPLICATIONS THAT MAY ARISE.
WARNING:
Before installing or maintaining the luminary, make sure all powers are
TURNED OFF
.
Verify that supply voltage is correct by comparing it with the label information on all
fixtures.
Make all connections in accordance with the NEC requirements, and make sure all
luminaries are properly secured to prevent any wire complications. This luminary is
to always be installed with the lens facing down and its not to exceed the maximum
ambient temperature rating noted on the specification sheet.
TRUNNION MOUNT
USSLxxxWPL
Series LED Area Light
Installation Sheet
STANDARD INSTALLATION STEPS
DRILLING TEMPLATE
4.6875 in
2.375 in
3.50 in
1.5625 in
1.1875 in
0.375 in
1. Use provided Hole Pattern for drilling. Make sure to
make an extra notch for the power cables to run through
the surface.
2. Place mount against surface
3. Install [6] bolts to secure the Trunnion Mount firmly in
place. Make sure all bolts are tightened and holes are
properly sealed.
7. Adjust the Tilt Angle on the
luminaire,
once the Tilt Angle is as
desired, finish
tightening the Socket
Head bolt to firmly
tighten the F2SB with
the Trunnion
Mount.
LED DRIVER
V(-)
[BLACK]
V(+)
[RED]
TO LOAD
[LED BOARD]
[WHITE]
[BLACK]
ACN [BLUE/WHITE]
ACL [BROWN/BLACK]
GROUND [GREEN]
NEUTRAL [WHITE]
GROUND [GREEN]
HOT [BLACK]
INPUT
OUTPUT
DIM
WHITE (-)
BL
UE(+)
Inside F2SB
PRE-CONNECTED
(DO NOT DISCONNECT)
Using a J-Box (not included), Connect the ACL and the ACN from the driver to the conduit with the AC Power Supply cords.Follow the Wiring Diagram provided.
* LED DRIVER Input Ground (green) wire only available for selected fixtures.
If the Ground Wire is missing and the Power Supply includes a ground wire, connect the power supply ground wire to the fixture.
(FOR DIMMABLE VERSION)
CAUTION:
PLEASE FOLLOW THIS INSTRUCTION MANUAL CAREFULLY TO
PREVENT ANY INJURIES OR COMPLICATIONS THAT MAY ARISE.
WARNING:
Before installing or maintaining the luminary, make sure all powers are
TURNED OFF
.
Verify that supply voltage is correct by comparing it with the label information on all
fixtures.
Make all connections in accordance with the NEC requirements, and make sure all
luminaries are properly secured to prevent any wire complications. This luminary is
to always be installed with the lens facing down and its not to exceed the maximum
ambient temperature rating noted on the specification sheet.
Includes:
F2SB048, F2SB080,
F2SB100,
F2SB150,
F2SB200,
F2SB300
F2SB Series LED Area Light
Installation Sheet
0200015-170815-1
Need help? Tech help line:
(800) 988-6386
Email:
Website:
www.paclights.com
Copyright © 2017 PacLights
All Rights Reserved Note: Instructions are subject to change at any time without notice
(F2SB048)
STANDARD INSTALLATION STEPS
MOUNTING METHODS:
Please select the installation instructions based on proper mounting method:
SKU
Description
AC2SBF
Slipfitter Mount for 2 3/8 inch OD (2” Pipe
Bracket) Tenon (0º to 90º Vertical Aiming Angle)
AC2SBTM Trunnion Mount
AC2SBAM1 6” Arm Mount for Square Pole
AC2SBAM2 6” Arm Mount for Round Pole
LED DRIVER
V(-)
[BLACK]
V(+)
[RED]
TO LOAD
[LED BOARD]
[WHITE]
[BLACK]
ACN [BLUE/WHITE]
ACL [BROWN/BLACK]
GROUND [GREEN]
NEUTRAL [WHITE]
GROUND [GREEN]
HOT [BLACK]
INPUT
OUTPUT
DIM
WHITE (-)
BL
UE(+)
Inside Junction Box
(Not Included)
PRE-CONNECTED
(DO NOT DISCONNECT)
1. Connect the ACL and the ACN from the driver to the conduit with the AC Power Supply cords.Follow the Wiring Diagram provided.
* LED DRIVER Input Ground (green) wire only available for selected fixtures.
If the Ground Wire is missing and the Power Supply includes a ground wire, connect the power supply ground wire to the fixture.
(FOR DIMMABLE VERSION)
AC2SBF
AC2SBAM1
AC2SBAM2
AC2SBTM
TROUBLESHOOTING
1) Make sure the Power Outlet matches the Voltage on the driver. It is very
important for the Power Outlet and the driver to match. If these values do not match,
this can cause the LED fixture to not turn on or damage the driver.
2) Check the LED Driver Input Connections. Make sure the ACL on the driver is
connected to the hot power outlet cable and the ACN on the driver is connected to the
Neutral wire on the power outlet.
3) Check the LED Driver Output Connections. These connections will already come
installed when the fixture is purchased. However, if the Input Connections are double-
checked and the lumen is not turning on. It might be a good idea to make sure there are
no cuts in the wires and everything is properly connected.
Please select the installation instructions based on proper mounting method:
SKU
Description
AC2SBPS Photocell,Twist Lock, 1.5 FC, 120-277 vAC, Instant On, 2-5 sec
OFF Delay
AC2SBPS480 Photocell,Twist Lock, 1.5 FC, 480 vAC, Instant On, 2-5 sec
OFF Delay
AC2SBSU Surge Protector. VMAX AC: 277v, maximum Lightning Surge
Current: 20,000A
AC2SBSU480 Surge Protector. VMAX AC: 277v, maximum Lightning Surge
Current: 20,000A
OPTIONAL ADDONS
5.
Run the power cord from the
trunnion
mount to the luminaire,
Once the cable
has been inserted
inside the
luminaire
,
connect the power
cable to the LED
Driver inside the
fixture
.
In order to
access the LED Driver
cables, the
electrician must first remove the [6]
screws from the service door using a #2
Phillips
screw driver and make all
connections inside the luminaire.
6.
Once all wiring is complete,
Close the service door and use
the M12 bolt to fasten the
Trunnion Mount to the
luminaire
.
Do not fasten completely.
4. Once the Trunnion Mount is properly
fastened to the mounting surface, run the
power cord cable from the inside of the
mounting surface and out notch from the
Trunnion Mount.
