background image

 

PROGRAMING CHANNELS 

 

All floor panels originally come from the factory unprogrammed to any one of the four channels and the 
panels will not respond to the handheld remote. To make the floor panel respond to the handheld 
remote control, make the following steps. 

Install two fresh AAA batteries into the handheld 

Remote Control

. While using the remote during 

assembly, you will have an opportunity to assign channels as each 

Floor Panel

 is connected to power.  

As the floor system is assembled, the 

Power Supply

 must be plugged into power, powered on and 

connected to the floor trim. The moment you connect a 

Floor Panel

 to power you will have 3 seconds to 

press one of the 

four channels’ “ON” button

s of the handheld 

Remote Control

. The four buttons are 

pointed out below. 

 

 

 

Channel 1 

 

   Channel 2 

 

        Channel 3 

 

               Channel 4           

 

NOTE: If the floor panel is new, or does not respond to the remote control, skip steps 1 thru 3. 

 
STEP 1: 
Changing or reprograming to a new channel will always require that the 

Floor Panel

 is first 

unprogrammed from the channel it is currently assigned.  To establish what channel the panel is 
currently assigned, simply press the on and off button of each channel until the panel responds. 
STEP 2: 
Disconnect the 

Floor Panel

 from power and then reconnect. Within 3 seconds press an

d hold the “ON” 

button of the currently assigned channel. 
STEP 3: 
If successful, 

ILLUMA SQUARE

 will flash white 9 times quickly. If not, repeat steps 1 and 2. 

STEP 4: 
Disconnect the panel from power. 
STEP 5: 
Reconnect to power and within 3 seconds, press o

nce (do not hold) the “ON” button of the channel you 

want the panel to be assigned to. 
STEP 6: 
If successful, 

ILLUMA SQUARE

 will flash white slowly 2 times. If not, repeat steps 4 and 5. 

Copyright USA Dance Floor, LLC 

Summary of Contents for ILLUMA SQUARE A















Reviews: