US Water Systems Fusion Service Manual Download Page 28 | Manualshive

Page: 28 / 34

background image

3.

Press the Extra Cycle button. Use this display to adjust the Regeneration Time. This option setting is identified by “RT” in the
upper left hand corner of the screen.

4. Press the Ex

tra Cycle button. Use this display to adjust the Feed Water Hardness. This option setting is identified by “H” in the

upper left hand corner of the screen.

Range: 1-199 hardness

5. Press the Extra Cycle button. Use this display to adjust the Fixed Reserve

Capacity. This option setting is identified by “RC” or

"SF" in the upper left-hand Corner of the screen.

6.

Press the Extra Cycle button. Use this display to set the Current Day of the Week. This option setting is identified by “CD” in the
upper left hand corner of the screen.

7. Press the Extra Cycle button to end User Programming Mode.

«
...
26
27
28
29
30
...
»

Summary of Contents for Fusion



































Reviews:

No comments

Related manuals for Fusion

Brand: A.O. Smith Pages: 2

Brand: A.O. Smith Pages: 2

Brand: FBD Pages: 40

Brand: Aurora Scientific Pages: 14

Fre-Heater D Series

Brand: Mueller Pages: 34

ARCTIC Compact 8L

Brand: Ugolini Pages: 36

Brand: Tier1 Pages: 18

Brand: GBG Pages: 83

Tork Xpressnap H-4580

Brand: U-Line Pages: 2

Portable H2 Server

Brand: Youngwoo Waterline Pages: 11

Brand: Boschetti Industrie Meccaniche Pages: 24

Brand: SPT Pages: 8

Brand: Ebac Pages: 12

Brand: Soleus Air Pages: 9

Aqua Sub WA2-02-50

Brand: Soleus Air Pages: 10

Brand: Ariston Thermo Pages: 16

Brand: Bock Water heaters Pages: 40

Brand: Grindmaster Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands