Upright X27-33RT Service & Parts Manual Download Page 92

Page: 92 / 134

TITLE

AUTO LEVEL

SWITCH

STOW

Platform Control Box Assembly
Sheet 2, Snorkel Models
SR3370 & SR2770

Revised 16-08-2006

LOWER FROM PLATFORM

LOWER BASE END OF CONTROL CABLE

J10.11

PIN #

JS 1

J10.9

PLATFORM GROUND WIRE
RAISE FROM PLATFORM

J10.10

OUTRIGGER RF DOWN

J10.1
J10.2
J10.3
J10.4
J10.5
J10.6
J10.7
J10.8

OUTRIGGER LF DOWN
OUTRIGGER LR DOWN
OUTRIGGER RR DOWN
OUTRIGGER RF UP
OUTRIGGER LF UP
OUTRIGGER LR UP
OUTRIGGER RR UP

OUTRIGGER SUPPLY

NOTE: JS 18 T’S IN CONTROL CABLE TO J1.6 AND J12.1

NOTE:

J12.1

FWD/DOWN

REV/UP

DOWN

HI / LOW DRIVE
SWITCH

FWD

REV

JS 2
JS 3
JS 4
JS 5
JS 6
JS 7
JS 8
JS 9
JS 10
JS 11
JS 12
JS 13
JS 14
JS 15
JS 16
JS 17
JS 18
JS 18
JS 19
JS 20
JS 21
JS 22
JS 23
JS 24
JS 25
JS 26
JS 27
JS 28
JS 29
JS 30
JS 31

J1.12

J1.11

J1.9

J1.1
J1.2
J1.3
J1.4
J1.5
J1.6

J2.6
J2.7
J2.8
J2.9
J2.10
J2.11
J2.12

J2.3
J2.2
J2.1
J2.4

INPUT FROM JSR (JS 15) ONLY
IF LOWER PLATFORM SWITCH IS MADE!

PLATFORM SPEAKER

PROPORTIONAL CONTROL

HI/LOW DRIVE SWITCH

OUTRIGGER SUPPLY

DRIVE FORWARD

DRIVE REVERSE

PROPORTIONAL HIGH OUTPUT

PLATFORM KEY SWITCH OUT

PLATFORM SPEAKER

START SWITCH FROM PLATFORM

STEER LEFT

POWER TO PLATFORM (14 GA)

STEER RIGHT

CHOKE/GLOW PLUG SWITCH AT PLATFORM
OPERATOR HORN
LIFT ENABLE LAMP
PLATFORM LOW OIL PRESSURE LAMP
PLATFORM DRIVE ENABLE LAMP

JS 25

JS 29

JS 26

JS 30

JS 17

JS 1
JS 3

JS 16

JS 6

JS 9
JS 11

JS 4

JS 12

JS 14

JS 7

JS 10

NOTE: NOT USED ON MACHINES WITHOUT STABILISERS

Platform Control Box Assembly drawing

Sheet 2

Page 3-16

Summary of Contents for X27-33RT




































































































































Search results

Summary of Contents for X27-33RT

Reviews:

Upright X27-33RT, Service & Parts Manual, Page: 92 / 134

Search results

Summary of Contents for X27-33RT

Reviews: