Upright X20N Service Manual Download Page 76

Page: 76 / 102

Drive Motors and Hubs

Section 2 - Service and Repair

Page 2-34

114101-000 X26 Ultra Narrow - Service Manual

E A R

H E E L S

, H

U B S

A N D

E A R I N G S

Figure 2-29:

Rear Hubs

EMOVAL

1. Chock the front wheels to prevent the

machine from rolling.

• Use a 1000 Kg (

1 ton

) capacity jack

to raise the front of the machine.

• Place two 1000 Kg (

1 ton

) jackstands

beneath the machine for support.

• Remove the jack.

2. Remove the wheel bolts and wheel.

3. Remove the dust cap, cotter pin, slotted

nut, and washer.

4. Slide the entire hub assembly from the

spindle.

5. Remove the outer cone bearing.

6. Remove the grease seal.

7. Remove the inner cone bearing.

8. Examine the bearing cups. If they are

smooth, shiny and free of pits or any
surface irregularities,

DO NOT

remove

them.

• If the cups need replacement, remove

them by tapping around the circum-
ference of the inside surface of the
cups from the opposite side using a
long drift.

NSTALLATION

Figure 2-30:

Bearing Cup Installation

1. Install the new bearing cups (refer to Figure 2-30):

• Position the replacement bearing cup over the opening in the hub

assembly.

• Position the worn cup over the replacement so that the bearing sur-

faces face each other.

• Use the old bearing cone as a drift to work the replacement into

position by tapping evenly around the circumference.

2. Apply a liberal coating of multipurpose grease to the bearing surface

of each cup.

3. Pack the inner bearing with multipurpose grease and position it into

the inner bearing cup.

4. Press a new grease seal into the hub assembly.

5. Apply a thin coating of multipurpose grease to the spindle to protect

the grease seal, then slide the hub assembly onto the spindle.

6. Pack the outer bearing with multipurpose grease and slide it onto the

spindle until it seats in the outer bearing cup.

7. Install the washer and slotted nut.

8. While rotating the hub, tighten the slotted nut until the hub drags, then

back the nut to the first slot that aligns with the cotter pin hole in the
spindle.

9. Install a new cotter pin and bend the end up over the nut and spindle.

10. Install the dust cap

11. Install the wheel and wheel bolts. Torque to 108 N-m (

80 ft./lbs.

1. Chassis
2. Wheel Bolts and Wheel
3. Dust Cap, Cotter Pin, Slotted

Nut and Washer

4. Hub Assembly

5. Outer Cone Bearing
6. Grease Seal
7. Inner Cone Bearing
8. Bearing Cup
9. Spindle

Old

Bearing Cup

New

Bearing Cup

REMOVE BEARING CUP

INSTALL BEARING CUP

Bearing Cup

Drift

Summary of Contents for X20N







































































































Search results

Summary of Contents for X20N

Reviews:

Related manuals for X20N

Brands by name

Popular brands

Upright X20N, Service Manual

Search results

Summary of Contents for X20N

Reviews:

Related manuals for X20N

Brands by name

Popular brands