background image

18

AK41  CHASSIS  PRODUCTION  MODE ADJUSTMENTS  PROCEDURE

A) PRELIMINARY

  All system, geometry and white balance alignments are performed in production service mode. Before starting the

production mode alignments, make sure that all manual alignments are done correctly. To start production mode

alignments enter the MAIN MENU  and enter the  code 

1675

 by pressing digit keys. Production mode items will appear

on the screen. Production mode groups will be displayed with different colours of headlines , so in order to access a

production alignment group press the colour key of the related group on the remote control transmitter.  After selecting

one of  the production service mode groups, you can access its items by pressing the cursor-up and/or cursor-down

keys. You can change the value of an item by pressing cursor-left and/or cursor-right keys on the remote control

transmitter.

In order to switch between other group of items press the colour key of this groups headline.

To store the settings press OK key. In order to leave this menu press MENU key.

B) HORIZONTAL AND VERTICAL GEOMETRY ALIGNMENTS

  - 

Switch the program to crosshatch test pattern.

  - Press RED key to access this group of item.

  - Select the items by pressing cursor-up and/or cursor-down keys.

  - Adjust the item by pressing cursor-left and/or cursor-right after selecting that item.

  - Store the settings by pressing OK key.

  - Switch to another item group by pressing the colour keys of the related coloured headline of that group.

  - Exit  production mode by pressing the MENU key on the remote transmitter..

1) V-SHIFT

  - Press cursor-left and/or cursor-right  buttons till the test pattern is vertically centred, i.e. horizontal line at the centre of

the test pattern is in equal distance both to upper and lower side of the picture tube. Check and readjust V-SHIFT item if

the adjustment becomes improper after some other geometric adjustments are done

2) V-SIZE

  -

 Press cursor-left and/or cursor-right buttons till horizontal black lines on both the upper and lower part of the test

pattern become very close to the upper and lower horizontal sides of picture tube and nearly about to disappear. Check

and readjust V-SIZE item if the adjustment becomes improper after some other geometric adjustments are done.

3) H-SHIFT

  - 

Adjust H-SHIFT item by pressing cursor-left and/or cursor-right buttons till test pattern is horizontally in equal distance

both to right and left sides of the picture tube. Check and readjust H-SHIFT item if the adjustment becomes improper

after some other geometric adjustments are done.

4) H-SIZE

Adjust H-WIDTH item by pressing cursor-left and/or cursor-right buttons till no under-scan condition will happen, i.e. no

white bars on the left and right side of the test pattern will be visible nor the picture will be so wide. Check and readjust H-

WIDTH item if the adjustment becomes improper after some other geometric adjustments are done.

5) S-COR

- Press cursor-left and/or cursor-right buttons till the size of squares on both the upper and lower part of test pattern

become equal to the squares laying on the vertical centre of the test pattern. Check and readjust S-COR item if the

adjustment becomes improper after some other geometric adjustments are done.

6) LINRT

- Press cursor-left and/or cursor-right buttons till all the size of squares of the test pattern become in equal size  from the

top of the screen to its bottom of the whole screen. Check and readjust LINRT item if the adjustment becomes improper

after some other geometric adjustments (especially after than S-COR adjustment are done.

7) ANGLE

- Press cursor-left and/or cursor-right buttons till the vertical lines of the crosshatch pattern become completely

perpendicular to horizontal lines without any angle of vertical deviation. Check and readjust ANGLE item if the adjustment

becomes improper after some other geometric adjustments are done.

8) BOW

- Press cursor-left and/or cursor-right buttons till the vertical lines especially ones close to the left and right sides will of

equal and symmetrical bending, i.e. they together  will neither  be towards left side nor right side. Check and readjust

BOW item if the adjustment becomes improper after some other geometric adjustments are done.

9) TRPEZ

-

 Press cursor-left and/or cursor-right buttons till vertical lines, especially lines at the sides of the picture frame became

parallel to the both sides of picture tube as close as possible. Check and readjust TRPEZ item if the adjustment

becomes improper after some other geometric adjustments are done.

10) PARAB

- Press cursor-left and/or cursor-right buttons till vertical lines close to the both sides of the picture frame become parallel

to vertical sides of picture tube without any bending to left  or to right side of the screen.. Check and readjust PARAB

item if the adjustment becomes improper after some other geometric adjustments are done.

Summary of Contents for FT-81031















































Reviews: