background image

TRF-ZW2 Buttons

Sync Button

 

To carry out a manual setup of devices, tap the Sync button on the 
controller. To exit the inclusion mode on the controller, tap the 
Sync button again. To exclude a Z-Wave product from the network, 
hold the Sync button down for 3 seconds. (Figure 2-1)

 
WPS Button

 

Easy push button inclusion for Wi-Fi devices.

 

(Figure 2-1)

 
Reset Button

 

The URC controllers can be reset to factory defaults by 
holding the reset button for 20 seconds and releasing it. This will 
reset the Z-Wave network and change it’s House ID, and clear your 
account and user configuration data from your controller.

The account will only be removed from the controller, but it will 
continue to be in the database.

Holding the reset button for 10 seconds will reset the network 
configuration settings to defaults, while keeping your other 
settings intact. (Figure 2-1)

Note: 

If this controller is the primary controller for your network, 

resetting it will result in the nodes in your network being orphaned and 
it will be necessary after the reset to exclude and re-include all of the 
nodes in the network.  If this controller is being used as a secondary 
controller in the network, use this procedure to reset this controller 
only in the event that the network primary controller is missing or 
otherwise inoperable.

A

B

C

Figure 2-1:

 TRF-ZW2 Side

A

B

C

Service

Z-Wave

Wi-Fi

WAN

Power

Summary of Contents for TRF-ZW2



























Reviews: