Universal Remote Control Complete Control MRF-260 Installation Manual Download | Manualshive

Page: 12 / 16

background image

Page 9

MRF-260 B

ASE

S

TATION

In the figure below, each device is set to a specific flasher.

Note: Remember, the MRF-260 will only respond to selections 1
through 4.

Step 5 - Make sure that the ID# is set on both the remote and on
the wheel of the MRF-260.
Click on the Receivers button and set the RF address to one of the
first 15 addresses (1-9 or A, B, C, D or E). The second set of address-
es is only supported by MSC units.

Step 6 - Close the RF window and Download to the Remote.

«
...
10
11
12
13
14
...
»

Summary of Contents for Complete Control MRF-260

















Reviews:

No comments

Related manuals for Complete Control MRF-260

Brand: Bard Pages: 8

Brand: Bardiani Valvole Pages: 35

Brand: Samson Pages: 56

Brand: Hach Pages: 128

Brand: Yamato Pages: 33

Brand: CAME Pages: 98

Brand: CAME Pages: 16

Brand: CAME Pages: 8

GA Industries 930-DT

Brand: Vag Pages: 4

Brand: DAQ Pages: 63

Brand: Danfoss Pages: 16

Consolidated 2900-40 Series

Brand: Baker Hughes Pages: 80

Brand: Quickie Pages: 64

Brand: Kamstrup Pages: 7

Brand: Telit Wireless Solutions Pages: 45

Brand: YOKOGAWA Pages: 33

Brand: Fagor Pages: 8

Brand: Anritsu Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands