MAN.270SF.REVB.102018
Page 5 of
18
3.0
Product Identification
270SF (subflange design) Gas Sample Probe for General Purpose & Hazardous Areas
Additional Options Shown on Next Page
270SF Model Extraction Sample Probe (Items marked with ** are not available on FM and ++ for ATEX hazardous area probes All
Sample Probes are Configured and Sold WITHOUT probe tubes (Stinger, Quill, Straw)
Chamber Material (Part Number Configurator: 270)
SF
316 Stainless Steel <400˚F (204˚C) (Standard) -Sub-Flange Mount
CF
Hastelloy C-276 < 400˚F (204˚C) -Sub-Flange Mount
TF
316 Stainless Steel w/TFE Coating < 400˚F (204˚C) -Sub-Flange Mount (no chamber isolation valve option)
NF
316 Stainless Steel w/ SilcoNert™ 2000 Coating < 400˚F (204˚C) -Sub-Flange Mount
SHF
316SS Hi Temp w/Kalrez® < 550˚F (288˚C) -Sub-Flange Mount
CHF
Hastelloy C-276 Hi Temp w/Kalrez® < 550˚F (288˚C) -Sub-Flange Mount
NHF
316 Stainless Steel w/ SilcoNert™ 2000 Coating Hi Temp w/ Kalrez® < 550˚F (288˚C) -Sub-Flange Mount
xxxU
xxxV
For Chamber Isolation Valve, add a 'U' to the End of the Chamber Material Selection for Unheated
For Chamber Isolation Valve, add a 'V' to the End of the Chamber Material Selection for Heated **++
Unheated - 316SS Valve, Monel (used with Hast. C-276 chamber), 316SS SilcoNert™ 2000
Low Temp (heated to 270 °F) - 316SS Valve, Monel (used with Hast. C-276 chamber), 316SS SilcoNert™ 2000
High Temp (heated to 550 °F) - 316SS Valve, Monel (used with Hast. C-276 chamber), 316SS SilcoNert™ 2000
Flange Size (Other Sizes Available, Consult the Factory)
F1
1.5" Flange
F2
2" Flange
F3
3" Flange
F4
4" Flange
F6
6" Flange
F1T
1.5" Flange - Top Dead Center
F2T
2" Flange - Top Dead Center
F3T
3" Flange - Top Dead Center
F4T
4" Flange - Top Dead Center
F6T
6" Flange - Top Dead Center
Chamber Heat Control
340
340°F (171°C) Temp Switch (Standard) - Mandatory for FM/ ATEX Approved Units (Standard)
375
375°F (190°C) Temp Switch**++
550
550°F (288°C) Temp Switch**++ (use high temp chamber in Chamber Material)
R
RTD Only**++ (includes 550 °F safety switch)
K
T/C Only, Type K**++ (includes 550°F safety switch)
J
T/C Only, Type J**++ (includes 550°F safety switch)
Blowback Type
BB
Blowback (Standard)
BT
Blowback w/ Smart Timer (Same as system voltage, 115 or 230 VAC. BB valve must match)**++
HB
Heated Blowback**++
HT
Heated Blowback w/Smart Timer (Same as system voltage, 115 or 230. BB valve must match)**++
N
No Blowback
Blowback Port
S
Standard Blowback
P
Blowback Probe Tip Filter Only -
No Chamber Blowback
N
No Blowback
Blowback Valve
24
24 VDC Actuator
1
115 VAC Actuator
2
230 VAC Actuator
A
Pneumatic Actuator
N
No Blowback
Enclosure (If Heatshrink Boot is other than 3", identify size after enclosure designator)
2 = 0.75" - 1.6" (19.05mm - 40.64mm) Dia.
3 (Standard) = 1.38" - 2.75" (35.05mm - 69.85mm) Dia.
4 = 1.43" - 4.47" (36.32mm - 113.54mm) Dia.
FG
Fiberglass Enclosure (Standard), 3" Boot
FI
Fiberglass Enclosure, Insulated, 3" Boot
SS
Stainless Steel Enclosure, 3" Boot
SI
Stainless Steel Enclosure, Insulated, 3" Boot
Enclosure Heat Control (Heating requires Insulated Enclosure)
N
No Enclosure Heat (Standard)
T
225°F (107°C) Temp Switch** (ATEX Enclosure uses a 150°F (65°C) T-Stat)
K
T/C Only, Type K**++
J
T/C Only, Type J**++
R
RTD Only**++
Power/Classification
1
115 VAC General Purpose
2
230 VAC General Purpose
1FM
115 VAC Approved for Class I, DIV. II, Grp. B, C, D (FM/ CSA)
2FM
230 VAC Approved for Class I, DIV. II, Grp. B, C, D (FM/ CSA)
1EX
115 VAC ATEX Approved for Zone IIC (TUV)
2EX
230 VAC ATEX Approved for Zone IIC (TUV)
Filter
2
2μm Ceramic (standard)
1
1μm Ceramic
C
0.1μm Ceramic coated
S
2μm Sintered 316SS
