Unitronics V130-33-TR6 Installation Manual Download Page 4 | Manualshive

Page: 4 / 12

background image

Vision™PLC+HMI Installation Guide

4

Unitronics

V430J

Caution



The necessary torque is 0.4 N·m (4 kgf·cm).

\

DIN-rail Mounting (V130/V350/V130J/V350J)

1. Snap the controller onto the DIN rail as

shown in the figure to the right.

2. When properly mounted, the controller is

squarely situated on the DIN-rail as
shown in the figure to the right.

«
...
2
3
4
5
6
...
»

Summary of Contents for V130-33-TR6













Reviews:

No comments

Related manuals for V130-33-TR6

Brand: NEC Pages: 304

Brand: Panasonic Pages: 31

Brand: Panasonic Pages: 31

Brand: Panasonic Pages: 26

Brand: NAiS Pages: 199

Brand: Panasonic Pages: 38

Brand: Panasonic Pages: 64

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 179

Brand: Panasonic Pages: 23

Brand: Panasonic Pages: 30

Brand: Panasonic Pages: 26

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 44

Brand: Panasonic Pages: 20

INDUSTRY PAN9028

Brand: Panasonic Pages: 34

Harmony Controller 2000

Brand: A10 Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands