background image

HMI Panel Installation Guide  

 

 

Unitronics 

 

 

Before You Begin 

 

 

Before installing the device, the installer must: 

 

Read and understand this document. 

 

Verify the Kit Contents.  

Note that the CPU-for-Panel is intended to be installed on the back of an HMI panel in 
accordance to a separate installation guide supplied with the CPU-for-Panel.   

 

Alert Symbols and General Restrictions 

When any of the following symbols appear, read the associated information carefully. 

Symbol 

Meaning 

Description 

 

Danger 

The identified danger causes physical and property damage. 

 

Warning 

The identified danger could cause physical and property damage. 

Caution 

Caution 

Use caution. 

 

All examples and diagrams are intended to aid understanding, and do not guarantee 

operation. Unitronics accepts no responsibility for actual use of this product based on 

these examples. 

 

Please dispose of this product according to local and national standards and regulations. 

 

This product should be installed only by qualified personnel. 

 

 

Failure to comply with appropriate safety guidelines can cause severe injury or 

property damage. 

 

Do not attempt to use this device with parameters that exceed permissible levels. 

 

Do not connect/disconnect the device when power is on. 

 

Environmental Considerations 

 

 

 

 

Ventilation: 10mm (0.4”) of space is required between the device top/bottom edges 

and the enclosure’s walls. 

 

Do not install in areas with: excessive or conductive dust, corrosive or flammable 
gas, moisture or rain, excessive heat, regular impact shocks or excessive vibration, 

in accordance with the standards and limitations given in the product’s technical 

specification sheet. 

 

Do not place in water or let water leak onto the unit.  

 

Do not allow debris to fall inside the unit during installation. 

 

Install at maximum distance from high-voltage cables and power equipment. 

Caution

 

 

The UniStream™ HMI Panel is designed to comply with NEMA 4X, IP66 and IP65. 

Note however that the Audio Protection Seal must remain plugged in for NEMA 

4X and IP66, in which case the audio sound level from the internal speaker is 

significantly reduced.  

 

 

 

Summary of Contents for UniStream USP-070-B10









Reviews: