Unitronics GW-BAC1 User Manual Download Page 5 | Manualshive

Page: 5 / 28

background image

Unitronics’s BACnet Gateway User Guide

Page 5 of 28

Unitronics

1

INTRODUCTION

1.1

GW-BAC1 Gateway

The GW-BAC1 is an external, high performance

Building Automation multi-protocol gateway

that has been

preprogrammed for enabling Unitronics products (hereafter called “device”) to various building automation
protocols. These protocols include BACnet®

1

MS/TP and BACnet/IP

2

. Configuration for the various protocols is

done via Unitronics configuration tool UniBACnet Configurator.

1.2

Record Identification Data

Each GW-BAC1 has a unique serial number located on the underside of the unit. This number should be
recorded, as it may be required for technical support.

1.3

Technical Support

For technical support and questions concerning setting up the GW-BAC1 to work with a Unitronics PLC
(e.g. Vision, UniStream etc.) please contact Unitronics technical support at

[email protected]

1

BACnet is a registered trademark of ASHRAE

«
...
3
4
5
6
7
...
»

Summary of Contents for GW-BAC1





























Reviews:

No comments

Related manuals for GW-BAC1

SmartNode 10100 Series

Brand: Patton Pages: 12

FiberPlex FPX6000 Series

Brand: Patton Pages: 20

SmartNode 4970 Series

Brand: Patton Pages: 57

Brand: S&C Pages: 9

Brand: RTA Pages: 66

Brand: Yeastar Technology Pages: 104

Brand: Hoymiles Pages: 2

Flight Stream 110/210

Brand: Garmin Pages: 46

Brand: Sagem Pages: 27

Brand: Zipato Pages: 36

Brand: David Clark Pages: 11

Brand: Cal Amp Pages: 164

Internet Security Gateway ZyWALL 100

Brand: ZyXEL Communications Pages: 708

ADSL2+ Ethernet/USB Gateway 660RU-Tx Series

Brand: ZyXEL Communications Pages: 286

Brand: SIMARINE Pages: 5

Brand: ViewSonic Pages: 34

Conquest HPO-9007 Series

Brand: KMC Controls Pages: 6

Ethernet Gateway V4

Brand: Packet Power Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands