background image

EX-RC1   

R e m o t e   I / O   Ad a p t e r

2/12

EX-RC1 Technical Specifications 

I/O module capacity 

Up to 8 I/O modules can be connected to a single adapter. The number of I/Os 
may vary according to module. 

Power supply 

12VDC or 24VDC  

Permissible range 

10.2 to 28.8VDC 

Quiescent current 

90mA@12VDC; 50mA@24VDC 

Max. current consumption 

650mA @ 12VDC; 350mA @ 24VDC 

Current supply for  
I/O modules 

800mA maximum from 5V. See Note 1 

Status indicators 

(PWR) 

Green LED—  Lit when power is supplied. 

(I/O COMM.) 

Green LED—  Lit when communication is established between the adapter to 

the other units. 
Blinks 0.5sec ON 0.5sec OFF when adapter is in Stop mode. 

(Bus COMM.) 

Green LED—  Lit when communication is established between the adapter and 

the OPLC. 

Notes

1.

 Example: 2 IO-DI8-TO8 units consume a maximum of 140mA of the 5VDC supplied by the adapter.

Communication

RS232 port 

Galvanic isolation 

No 

Voltage limits 

±

20V 

Cable length 

Up to 15m (50‘) 

CANbus port 

Nodes

60

Power requirements 

24VDC (±4%), 40mA max. per unit 

Galvanic isolation 

Yes, between CANbus and adapter 

Cable type 

Twisted-pair; DeviceNet® thick shielded twisted pair cable is recommended. 

Cable length/baud rate 

25 m 
100 m 
250 m 
500 m 
500 m 
1000 m* 
1000 m* 

1 Mbit/s  
500 Kbit/s 
250 Kbit/s  
125 Kbit/s  
100 Kbit/s  
50 Kbit/s  
20 Kbit/s 

* If you require cable lengths over 500 meters, contact

technical support.

Environmental

IP20/NEMA1 

Operating temperature 

0

°

to 50

°

C (32 to 122

°

F) 

Storage temperature 

-20

°

to 60

°

C (-4 to 140

°

F) 

Relative Humidity (RH) 

5% to 95% (non-condensing) 

Dimensions (WxHxD) 

80mm x 93mm x 60mm (3.15” x 3.66” x 2.36”) 

Weight

135g 

(4.76 oz.)

Mounting 

Either onto a 35mm DIN-rail or screw-mounted. 

Samara

tel. +7 846 273 95 85

[email protected]

Yekaterinburg

tel. +7 343 287 19 19

[email protected]

St. Petersburg

tel. +7 812 327 3752

[email protected]

Moscow

tel. +7 495 641 1616

[email protected]

Helsinki

tel. +358 9 540 4940

[email protected]

Vilnius

tel. +370 5 215 1646

[email protected]

Riga

tel. +371 6738 1617

[email protected]

Мinsk

tel. +375 17 200 0876

[email protected]

Tallinn

tel. +372 668 4500

[email protected]

Кiev

tel. +38 044 495 33 40

[email protected]

Summary of Contents for EX-RC1









Reviews: