background image

EX-RC1   

R e m o t e   I / O   Ad a p t e r

2/12

4

Unitronics

Setting the Unit ID Number 

The ID number range is from 1 to 60. 
The DIP switch settings represent the ID number as a binary value as shown in the following figures. 

Unit ID 

1 (Default)

2

59

60

Settings 

Connecting Expansion Modules 

An adapter provides the interface between the OPLC and an expansion module. To connect the I/O module to 
the adapter or to another module: 
1.

Push the module-to-module connector into the port located on the right side of the device.

Note that there is a protective cap provided with the adapter.  This cap covers the port of the final 
 I/O module in the system. 

To avoid damaging the system, do not connect or disconnect the device when the
power is on.

1

2

Component identification 

1

Module-to-module 
connector 

2

Protective cap 

Wiring 

Do not touch live wires.

Unused pins should not be connected.  Ignoring this directive may damage the device.
Double-check all wiring before turning on the power supply.
Do not connect the ‘Neutral or ‘Line’ signal of the 110/220VAC to the device’s 0V pin.
In the event of voltage fluctuations or non-conformity to voltage power supply specifications,
connect the device to a regulated power supply.
Double-check all the wiring before turning on the power supply.

Summary of Contents for EX-RC1









Reviews: