MACHINE PARTS AND CONTROLS
BACKWATER TANK
The backwater tank collects dirty water. It must contain a specific
quantity of water (between Min and Max), which acts as a filter.
Once the water is dirty, it must be changed, since it filters better
when it is clean.
FILTER BASKET
Located above the tank, the basket ensures proper filtering. It is
composed of a plastic base and a cylinder-shaped metal wire net
containing a float gauge, and is equipped with two polyester filters
(F1 and F2). The filter basket must always be kept clean, and it must
be carefully dried before the vacuum function is activated. Do not
use the machine if the polyester filters are not inserted in the filter
basket!
TANK COVER
The tank cover opens by pressing the handle button. It provides
access to the filter basket and the backwater tank to pour in the
filter water and perform regular cleaning operations. When closed,
the handle allows you to carry the machine easily. Do not press the
open button while lifting up the machine!
SUCTION/STEAM SOCKET
The suction/steam socket is protected by a small door, which can be
opened by pulling up on the notch. Cleaning and ironing devices can
be connected to the socket. It is equipped with electric contacts, a
steam connection, and a suction tube.
SIDE FILTER COVER
The side filter, which is manufactured in antistatic material, releases
water-filtered air into the environment. You should periodically check
the filter and replace it when necessary. A damaged or dirty filter
makes cleaning more difficult and can reduce the suction power of
the machine. To access the filter, simply open the side door where
it is located.
BOTTOM FILTER COVER
The bottom filter, located on the underside of the machine, prevents
dust from entering the motor’s cooling ducts. This filter is not part
of the cleaning circuit. Check it periodically and clean it with water
when necessary. Dry the filter before putting it back in place. To
access the filter, simply rotate the cover in the direction indicated by
the arrows. When the bottom filter is kept clean, the motor performs
better, preventing malfunctions.
POWER CORD COMPARTMENT
Located beneath the backwater tank, the power cord compartment
can be opened by pulling from the notch. It is used to store the power
cord tidily in between uses. The notch allows you to close the
compartment even while the power cord is extracted.
ANTENNA
The antenna, which is manufactured in stainless steel wire and
inserted into the two holes on the machine, supports part of the
weight of the flexible hose, helping to lighten work during cleaning.
Place the flexible hose on the antenna as shown in the figure. It
can be removed before putting the machine away.
FUNNEL CAP
The cap that covers the water tank can be opened while the boiler is
under pressure. To open it, pull up on the plastic ring. The cap also
acts as a funnel to fill the tank with water. Turn the plastic ring from
the position to the position. Pull the sliding piece up as shown
in the figure. Then, insert the cap, turned upside down, into the tank
opening. Before closing the tank with the cap, push the sliding piece
down into the closed position and turn the plastic ring to the original
position.
PRESSURE GAUGE
The gauge indicates the boiler pressure. It functions whether the
machine is plugged in or not.
MAIN ON/OFF BUTTON
BOILER ON/OFF BUTTON
MAIN ON/OFF INDICATOR
BOILER ON/OFF INDICATOR
MOTOR SPEED REGULATION BUTTON
Push the button towards the + symbol, to turn the suction motor on
and increase suction power. Push the button toward the – symbol to
decrease the motor power. The motor automatically turns off if the
button is held in either position for a few seconds. The suction power
is indicated by a red light indicator beneath the symbol: slow and
intermittent = low power, always on= maximum power.
IRON BUTTON
The iron button turns on the iron (optional). The light indicator beneath
the button will turn on when its pressed. The motor cannot be turned
on while the iron button is activated. The iron will not turn on if the
iron button is not pressed, even if it is hooked up to the machine.
PURIFIER BUTTON
The purifier button switches the motor onto the right speed for air
purification. The light indicator below the button will turn on when it
is pressed. Press the button again to stop the motor. The purifier button
cannot be activated if the boiler (on/off switch - 12) is on.
STEAM READY INDICATOR
This indicator lights up once the boiler has reached operating pressure.
Wait for it to light up before using the steam function. Once it has
lit up the first time, you can ignore the indicator status throughout
the rest of operation.
EMPTY TANK INDICATOR
This indicator goes on, accompanied by an acoustic signal (buzzer),
when the cold tank is empty. It indicates that the cold tank must be
filled with water (remove the funnel cap and follow instructions
provided in point 9).
ELECTRIC BRUSH ON/OFF INDICATOR
It indicates that the electric brush (optional) is ready for use. The
indicator turns off when the boiler is turned on.
> Machine Body
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
10
ENGLISH
Summary of Contents for C500A
