background image

11

 

 

 

IP 20001

(B) IN NO EVENT SHALL UNITED SAFETY’S LIABILITY, IN THE AGGREGATE, FOR DAMAGES 
ARISING OUT OF A BREACH OF THIS LIMITED WARRANTY, WHETHER IN TORT, CONTRACT OR 
OTHERWISE, TO BUYER OR ANY OTHER PERSON OR ENTITY EXCEED THE PRICE ACTUALLY 
PAID BY BUYER FOR THE WARRANTED UNIT. 
(C) IN NO EVENT SHALL UNITED SAFETY BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, 
INDIRECT, PUNITIVE, SPECIAL, OR SIMILAR DAMAGES, INCLUDING, WITHOUT LIMITATION, 
DAMAGES FOR LOSS OF PROFITS, LOSS OF GOOD WILL, WORK STOPPAGE, OR ANY AND ALL 
OTHER COMMERCIAL DAMAGES OR LOSSES, WHETHER DIRECTLY OR INDIRECTLY CAUSED, 
WHETHER IN TORT, CONTRACT, OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF 
SUCH DAMAGES. 
(D) THE LIMITATIONS OF LIABILITY IN CLAUSES (B) AND (C) ABOVE SHALL APPLY EVEN IF AN 
EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY FAILS OF ITS ESSENTIAL PURPOSE. 
 

NOTIFICATION: 

All reports, claims, or notices required by the warranty to be provided to UNITED SAFETY must be in 
writing and delivered to:  Attention – UNITED SAFETY Warranty Claim Department, 101 Gordon Drive, 
Exton, PA  19341 or emailed to 

[email protected]

 or to such other physical or email 

address as UNITED SAFETY requires from time to time.  Repairs being claimed for warranty must be 
sent to UNITED SAFETY for prior approval and warranty acceptance before any warranty claims can 
be made.   Parts being claimed for warranty must be sent to UNITED SAFETY for prior approval and 
warranty acceptance before any warranty claims can be made. 
 

INSPECTION AND VERIFICATION: 

The owner must provide access to each alleged defective Warranted Unit so that UNITED SAFETY's 
authorized representative can perform an on-site inspection.  Alternatively, UNITED SAFETY may ask 
the owner to ship the alleged defective Warranted Unit to UNITED SAFETY for inspection.  Within 90 
days of the inspection, either on-site or in the laboratory, UNITED SAFETY will render an opinion as to 
whether or not the claimed failure is covered by the warranty. 
 

MAINTENANCE: 

UNITED SAFETY provides the proper maintenance instructions as well as required service intervals 
with each Warranted Unit.  Warranty is contingent upon documented performance of recommended 
maintenance and service.  All replacement parts must be purchased from UNITED SAFETY or an 
authorized dealer of UNITED SAFETY, and the failure to purchase such parts from UNITED SAFETY 
or an authorized dealer of UNITED SAFETY will render this warranty null and void. 
 

DESIGN: 

UNITED SAFETY reserves the right to modify parts and design specifications without notice as long as 
the Warranted Unit meets general specifications, unless otherwise committed per contract. If changes 
outside the specifications in effect at the time of manufacturing the Warranted Unit have to be 
incorporated, UNITED SAFETY will submit such changes to Buyer for prior approval. 
 

OTHER: 

This Limited Warranty is contingent upon Buyer paying the purchase price for the Warranted Unit. This 
Limited Warranty supersedes any other terms including but not limited to Buyer’s terms printed on the 
back of Purchase Orders, listed on websites or other sources from buyers. 
 
Warranty – Active Air 

 

 

Summary of Contents for 20001















Reviews: