background image

Page 10 

 

655920 

Electra Steer Diagnosis Trouble Code Reading and Code Clearing 
 

1.  Verify that your trouble code light is on steady. 
2.  Next, take your purple or brown wire and connect it to a good clean ground. You 

will have to make sure it is a solid ground to get the LED to blink or flicker and 
you may have to use a jumper wire to extend the wire’s length. Once you see the 
LED flicker or blink wait for LED to start blinking a code. 

3.  The light will flash in a sequence like 1 and then 123. This code flash would be 

interpreted as a code 13. The code will repeat itself 3 times and then go to the next 
code if there is one in the system. You need to wait until all the codes are read and 
recorded. 

4.  Once you know what the codes are you can use this chart to tell where or what the 

problem may be. 

5.  Once you have determined what the problem is and make the necessary repairs, 

you can proceed to clear the codes by running a jumper wire from the white wire 
with the single spade connector on it to ground. 

6.  Verify the ignition is off. Place the white wire to ground. Turn key on, wait 5 

seconds and the light should go out. When the light goes out turn off ignition and 
remove jumper wire. Once all repairs are made turn ignition on and see that light 
proves out normally. This is all there is to it. 

 

Trouble Code 

 

Problem 

 

Diagnosis 

 

41-42-43-44- 

Electric motor  

Change Electric  

45-51  

Malfunction  

Motor  

11-13-14-15  

Torque Sensor  

Change Sensor  

52-54-55  

ECU  

Change  

 

Malfunction  

Computer  

22  

No Engine  

Computer Error  

 

Input  

 

21-23-24  

No Speed  

Computer Error  

 

Signal  

 

 

We welcome your suggestions & comments to make this or any of our installations better! If 

you have any questions or problems regarding this product please contact us at:

 

1555 Enterprise Parkway 

Twinsburg OH 44087 

800-338-9080 

WWW.UNISTEER.COM 

655920 

(1/9/09) 

 

 

 

Copyright © 2009 by Maval Manufacturing Corporation All rights reserved. 

 

No part of these materials can be reproduced or utilized in any form or by any means, 

electronic or mechanical, including photocopying, recording or by any information storage 
and retrieval system, without permission in writing from Maval Manufacturing Corporation.

 

Summary of Contents for 2009 Ranger ELECTRA-STEER











Reviews: