Unique Classic GP-30CR OF1 W Owner'S Manual Download Page 27 | Manualshive

Page: 27 / 48

background image

27

Oven Valve

The oven control has a fl ame safety device built into the body of the thermostat.
Presence of a gas ignition source (pilot) is verifi ed by a fl ame safety probe. This fl ame
safety probe actuates the internal safety device to allow gas into the oven burner
when the oven is turned on. If there is a loss of gas ignition during operation, the fl ame
safety device will close off gas fl ow to the oven burner and pilot.

The oven burner orifi ce is located on a brass injector stud at the rear of the oven
under the oven fl oor. This orifi ce is dedicated to the gas for which the oven is to be
used. The orifi ce is not adjustable. It must be changed completely to convert from one
gas to the other. DO NOT DISCARD THE UNUSED ORIFICE. It should be saved in order
to convert the range back to its original fuel.

ADJUSTING THE TOP BURNER AND OVEN FLAME

(continued)

INCORRECT AND GOOD FLAME PATTERNS

If burner ﬂ ames look like A, call for service.

B or C is normal burner ﬂ ames, depending on the type of
gas you use.

With LP gas, some yellow tipping on outer cones is
normal.

QUALITY OF FLAMES

The combustion quality of burner ﬂ ames needs to be
conﬁ rmed visually.

A. Yellow ﬂ ames — Call for service

B. Yellow tips on outer cones — It is normal for

LP gas

C. Soft blue ﬂ ames — It is normal for natural

gas

Incorrect:

ﬂ ame

lifting off the burner

Good fl ame:

Well-deﬁ ned blue

ﬂ ame with slight yellow tipping

Top Burner Height

In the pilot assembly shown below, the LPG oriﬁ ce is
0.14 mm. When doing the conversion from Propane to
Natural gas make sure the pilot oriﬁ ce is changed to
the NG oriﬁ ce sized at 0.2 mm. If you leave the LPG
oriﬁ ce 0.14 mm in place, the pilot ﬂ ame will may be too
small to keep the pilot lit.

Oven Pilot

The oven pilot is located along the left hand side of the oven burner. It is fastened to the
pilot assembly with the thermocouple and the electrode. The fl ame of the oven pilot
ignites main burner gas when the oven is turned on. If the pilot fl ame is not present, the
fl ame safety device will not allow pilot gas or main burner gas to fl ow.

THERMOCOUPLE

IGNITER

OVEN PILOT

PILOT ORIFICE

«
...
25
26
27
28
29
...
»

Summary of Contents for Classic GP-30CR OF1 W

















































Reviews:

No comments

Related manuals for Classic GP-30CR OF1 W

Brand: Sears Pages: 15

Brand: Jenn-Air Pages: 48

Brand: Jenn-Air Pages: 48

Brand: John Lewis Pages: 2

Brand: GE Pages: 32

Brand: Samsung Pages: 2

Brand: Samsung Pages: 60

Brand: Samsung Pages: 56

Brand: Samsung Pages: 56

Brand: Samsung Pages: 56

Brand: Samsung Pages: 80

Brand: Samsung Pages: 56

Brand: Samsung Pages: 56

Brand: Samsung Pages: 72

Brand: Samsung Pages: 66

Brand: Samsung Pages: 66

NE58 943 Series

Brand: Samsung Pages: 104

Brand: Samsung Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands