Unipulse M525B Operation Manual Download Page 45 | Manualshive

Page: 45 / 85

background image

36

4

　

FOR GREATER USE OF THE PRINTER

36

FOR GREATER USE OF THE PRINTER

Chapter

4

Set the number of code digits for classification.

Details of setting

Usually up to six digits can be used for code names, but if the Number of Code Digits is set,
code names are classified by the set number of digits from their ends, so that code names having
a different beginning can also be classified as the same for totaling.

Register a code table. What should be registered are codes and corresponding code names for the
code table.

Name of setting

23: Number of Code Digits Designation

Setting range

0 - 6 (digits)

Initial value

6

Caution

When using code tables, set the Number of Code Digits to two digits. If it is set
to three or more digits, normal classification cannot be performed.

Name of setting

24: Code Table Registration Ach
25: Code Table Registration Bch

Maximum number of codes

64 (32 for each ch)

Caution

- The code table can only be registered with the keys on the front panel.
- For details of the code table, see "6-1.Classification by Code Name and Code

Table" on page 46.

23: Number of Code Digits Designation

Example) The Number of Code Digits is set at two digits.

This part is printed but is not the
target of classification for totaling.

Classification is performed only with the last
two digits, which are the target of totaling.

①

①

②

①

②

Classification for totaling

０００００１

０００１０１

０００２０１

１００１０２

０００１０２

24,25: Code Table Registration Ach/Bch

«
...
43
44
45
46
47
...
»

Summary of Contents for M525B






















































































Reviews:

No comments

Related manuals for M525B

Brand: Xerox Pages: 25

Brand: Qilive Pages: 398

Perfecta 3600STP

Brand: Variquest Pages: 12

Perfecta 3600STP

Brand: Variquest Pages: 231

Awards Maker 400

Brand: Variquest Pages: 4

Brand: Lexmark Pages: 8

Brand: Partner Pages: 81

Multi-Font NX-2415

Brand: Star Micronics Pages: 134

Fast T-Jet Blazer Pro

Brand: Screen Print & Inkjet Pages: 138

Brand: Felix Storch Pages: 46

Brand: Xerox Pages: 214

Brand: Cardco Pages: 28

Brand: Oki Pages: 18

Phaser 6700V/DX

Brand: Xerox Pages: 162

Brand: Oki Pages: 276

Brand: Brightek Pages: 8

Brand: Lexmark Pages: 79

Brand: Oki Pages: 271

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands