background image

L

N

AC IN

HOLD S I F

F.G.

SET

8

0

4

8

C

1

5

9

D

2

6

A

E

3

7

B

F

9

SI/F terminal base

This is a terminal base for SI/F 
input (two-wire serial interface 
input).  The applicable wire 
material is a parallel 2-core 
cable, cabtyre cable, etc.

SIF

Frame ground

This  is  a  grounding  terminal.    Be  sure  to
ground this F.G terminal to prevent an electric
shock and a fault due to static electricity.

AC power supply
input terminal base

Connect the attached AC power cable.The input
voltage is 100 to 240 V AC and the frequency is
50/60 Hz.

Unipulse Corporation

9-11 Nihonbashi Hisamatsucho, Chuo-ku, Tokyo, 103-0005
Tel. +81-3-3639-6120   Fax. +81-3-3639-6130

Hold input terminal base

To hold the indicated value, 
strap these two terminals.  
The right-hand terminal is a 
COM terminal.

HOLD

+

-

Open-circut

OFF

Short-circuit

ON

Vcc

Iso

COM

Ic=Approx. 6mA

Input circut

 REAR PANEL

Indication contents selecting
rotary switch

Various data from the indicator 
can be selected and displayed 
by changing over the rotary 
switch.  The decimal point 
automatically follows the 
setting from the indicator.

SW No.

Contents of indication

0

Total weight indication

1

Net weight indication

2

Tare weight indication

3

Load cell indicator 
interrelated value (normal mode)

4

Load cell indicator 
interrelated value (LD151 compatible mode)

5

Digital indicator
interrelated value

8

Self-check mode

0

4

8

C

1

5

9

D

2

6

A

E

3

7

B

F

SET

External Dimensions

 

The plate thickness of the mounting panel is 1.5 mm or more.

 

Unit 

mm

92

+0.8

-0

96

56.8

45

+0.6 -0

 FRONT VIEW 

 SIDE VIEW 

(4)

L

N

AC IN

HOLD S I F

F.G.

SET

8

0

4

8

C

1

5

9

D

2

6

A

E

3

7

B

F

91

CZ

ZT

MD ZALM TARE NET GROSS

HOLD

LD514

 

EXTERNAL

 

DISPLAY

48

2.5

44

2

2

2.5

REAR VIEW 

PANEL CUT

DIMENSIONS

     Connecting to Cage Clamp Terminal Block

As the SI/F terminal and hold input terminal is using the cage clam
system terminal stand, connecting is simple.

1.Strip the casing 0.2in(6mm) on the cable to be connected.
2.Twist the bare wire to fit the terminal hole.

3.Insert the supplied screwdriver into the upper hole and lift

upward

4.Insert he twisted wires into the lower hole.

5.Pull the screwdriver out from the upper hole.
6.Make sure cable is clamped securely and does not come

out wight a slight tug.

Cable can be from 24 to 12AWG (0.2 to 2.5MM

2

).

It is not necessary to solder the cable wires or to
fix a solderless terminal

If several cables to be inserted to the same hole,

 twist those cable wires together and insert.

0.2in(6mm)

    
      

    

About the power cable

The power cable attached to this product as standard
equipment can be used in the AC100V power supply
in Japan. (Official ratings voltage AC125V)
Please use the power cable authorized in the country
when you use this product outside Japan.

Our company sells following resistance pressure
cable AC250V (European standard product) sepa-
rately.
Please purchase it from us when you need after con-
firming its plug shape/voltage.

CAAC3P-CEE7/7-B2 

: CEE7/7 Plug cable (2m)

Reviews: