Unipart Dorman HD ALT Operation And Maintenance Manual Download Page 3

 

Heavy Duty Assisted Lift Trunnion Operation and Maintenance Manual

 

Form Reference   

C64.65546

 

 

Issue 

5.00 

2 of 39 

Issue Date 

May 2021 

 

Document Control 

 
It is the reader’s responsibility to ensure they have the correct version of this document. If in 
doubt, please contact Unipart Dorman to verify the current issue status. 

 

Issue Number 

Dated 

Reason 

Jul 19 

 

Initial Issue 

Sep 19 

 

References to RBK-221 padlock added 

Nov 19 

 

Images and layout updated following feedback 
from Network Rail PA review. 

Jan 20 

 

Wording changes following Network Rail Product 
Acceptance and Ergonomics Review  

May 21 

 

Additional Safety Warnings  

 

Addition of extra information on signal alignment 
methods 

 

New section on Module Replacement 

 

 

Name 

Role 

Digital Signature 

Author 

Graham Scott 

Technical Sales Manager   

Checked by 

Mike Durham 

Design and Development 
Engineer 

 

Approved by 

John Lee 

Head of Design and 

Development 

 

 

 

 

 

 

 

 

 

 

 

 

 

Graham 

Scott

Digitally signed by Graham Scott 

DN: dc=local, dc=unipartrail, 

ou=Southport, ou=Departments, 

ou=Technical Sales, cn=Graham Scott, 

[email protected] 

Date: 2021.06.03 15:00:21 +01'00'

Digitally signed 
by: Mike Durham

Date: 2021.06.03 
15:18:33 Z

Mike 
Durham

Digitally signed by: John Lee
DN: CN = John Lee email = 
[email protected] OU
 = Southport, Departments, 
Technical

Date: 2021.06.03 15:27:21 Z

John Lee

Summary of Contents for HD ALT








































Reviews: