manualshive.com logo in svg

Unipart Dorman HD ALT, Operation And Maintenance Manual

Share
Download
Unipart Dorman HD ALT Operation And Maintenance Manual Download Page 18

 

Heavy Duty Assisted Lift Trunnion Operation and Maintenance Manual

 

Form Reference   

C64.65546

 

 

Issue 

5.00 

17 of 39 

Issue Date 

May 2021 

 

Using the lifting eyes highlighted in red shown in the image above, lift the HD ALT into position 
onto the four 24mm studs taking care to align the arrow marked on the Manufacturer Information 
Plate on the HD ALT baseplate parallel with the direction of the running rail. Then fit the remaining 

washers and nuts to secure it onto the studs  
 

Raising &Lowering the HD ALT  

 

The HD ALT is normally delivered to site in the horizontal position with the retaining pin secured 
in place with an R clip and a RBK-221 padlock.  

 

The Lockout warning tag and lanyards securing the pin and R Clip are not shown in this illustration for clarity 

A set of 8 off hex head bolts and washers are provided inside the electrical connection box to 
secure the trunnion in its vertical position. 

Summary of Contents for HD ALT








































Reviews:

No comments

Brands by name

Popular brands

Load more brands