Unimig KUMJRRW200AC/DC Operating Manual Download | Manualshive

Page: 28 / 48

background image

28

(1) Turn on the machine using the ON/OFF switch

(2) Select the preferred TIG function with the MODE selector switch

(3) Connect the TIG Torch connector to the negative terminal and tighten it

(4) Connect the Earth Cable connector into the positive terminal and tighten it

(5) Connect the torch switch remote lead into the torch remote socket

(6) Insert the torch gas connector into the quick lock gas receptacle

(7) Connect gas line to Gas Regulator and connect the gas regulator to the Gas Cylinder

Connect the gas line to the quick lock gas inlet connector at the rear of the machine

(7) Connect the regulator to the cylinder,

Connect the gas lead to the regulator.

Set the flow to 8-12 l/min

(4) Connect the Earth cable

connector to the terminal

(5) Connect the torch switch lead

to the torch remote receptacle

(1) Turn on the machine using the

ON/OFF switch.

(2) Select preferred TIG mode using

the MODE selector switch

(3) Connect the TIG torch connector

to the terminal.

(6) Insert the torch gas connector into

the quick lock gas receptacle.

Set Up Procedure for AC TIG Welding:

TIG Welding Set and Operation

Razorweld

Razor

weld

™

™

™

™

«
...
26
27
28
29
30
...
»

Summary of Contents for KUMJRRW200AC/DC

















































Reviews:

No comments

Related manuals for KUMJRRW200AC/DC

Brand: Radionics Pages: 10

Brand: N-Com Pages: 2

Brand: JBM Pages: 35

Brand: OMA Pages: 75

Brand: Magmaweld Pages: 8

AZ8350 - Cd Radio Cass Recorder

Brand: Magnavox Pages: 18

Brand: Magmate Pages: 20

Brand: SwissPhone Pages: 2

Brand: Modecom Pages: 28

Brand: Jensen Pages: 13

Brand: EAW Pages: 2

IQ PANEL 2 PLUS

Brand: QOLSYS Pages: 2

Brand: Air Liquide Pages: 66

Brand: Bear Pages: 21

Brand: Thermal Dynamics Pages: 40

Brand: Genie Pages: 44

Brand: Microlab Pages: 4

Weymouth Series

Brand: Hamworthy Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands