0.775V
1.44V
1V
GAIN
INPUT
Made in Taiwan
PARALLEL
PUSH TO RESET
~220VAC 50Hz
1800 WATTS
BRIDGE
NORMAL
STEREO
20Hz
200Hz
FREQUENCY
SUB
NORMAL
SUB
20Hz
200Hz
FREQUENCY
CH-2
CH-1
THRU
THRU
INPUT
INPUT
CAUTION
MINIMUM LOAD IMPEDANCE
2 OHM PER CHANNEL
4 OHM BRIDGE
Serial No.:
H-2
C
1+
1-
POS NEG
CH- 2
1+
1-
POS NEG
BRIDGE
H-1
C
K
C
O
L
K
C
O
L
K
C
O
L
1+
1-
POS NEG
CH- 1
LIFT
GROUND
Front Views & Rear Views
Introduction
Unpacking
Installation and Mounting
Front Panel
Operation
Mode Selection
Protection
Specifications
Rear Panel
X-3000 Rear Panel
10
24
14
12
11
20
23
26
Figure
5
21
page 6
18
19
15
16 13 17
22
25
10. Fan Outlet Ports
- Cooling air enters the amplifier through the front grills and exhausts through the fans. Be sure not to
block these ports when installing the amplifier or other associated equipment. Air must flow unimpeded through these
ports.
11. Channel 2 Subwoofer Mode On/Off Switch -
Turns the subwoofer mode for channel two on and off.
12. Channel 2 Frequency Adj. -
This pot adjust the frequency level sent to your speaker on channel two when using your
amplifier in subwoofer mode.
13. Channel 1 Frequency Adj.-
This pot adjust the frequency level sent to your speaker on channel one when using your
amplifier in subwoofer mode.
14. Channel 2 XLR Input -
Channel two 3-pin XLR balanced input jack.
15. Channel 1 XLR input -
Channel one 3-pin XLR balanced input jack.
16. Channel 1 Subwoofer Mode On/Off Switch -
Turns the subwoofer mode for channel one on and off.
17. Mode Selection Switch
- This recessed, three-position switch configures the amplifier for Stereo, Parallel or Bridged
Mode operation. Amplifiers are factory-configured for Stereo Mode. See section on Mode Selection for more information.
18. Channel 2 XLR THRU Jack -
Channel two 3-pin XLR balanced output jack.
19. Channel 1 XLR THRU Jack -
Channel one 3-pin XLR balanced output jack.
20.
Circuit Breaker
- X Series amplifiers have a circuit breaker - The circuit breaker shuts off during normal use, Please
switching off the AC power switch for a minute, Then turn on the AC power switch again, Push the circuit breaker to
reset the power. If the circuit breaker shuts off immediately, The amplifier needs servicing.
21. Channel 2 Speakon Output -
Use pins 1+ and 1- of this 4-pole Speakon connector to connect to your speakers input
jack.
22. Channel 1 Speakon Output -
Use pins 1+ and 1- of this 4-pole Speakon connector to connect to your speakers input
jack.
23. Bridged Speakon Output -
Use pins 1+ and 1- of this 4-pole Speakon connector to connect to your speakers input
jack.
24. Input Gain Switch
- This three position switch let you select different input sensitivities, respectively three different
Voltage gains. The switch setting are : 1.44V, 1V or 0.775V input sensitivity.
25. AC POWER Cord
- Connect to AC power supply. Be sure that the supplied volfage in your area matches the amplifiers
required voltage.
26. Ground Lift Switch
- This switch is used to disconnect the internal ground signal from the amplifier chassis ground.
This may reduce the buzz that is caused from an electrical 50Hz cycle.
X-3000 <2U MODEL> / X-4000 X-6000 <3U MODEL>
UNiK A
P R O F E S S I O N A L AU D I O
