Unika S-4000 User Instructions Download Page 15

Page: 15 / 16

page 14

UNiKA

S-4000/S-5000/S-6000

S-SERIES AMPLIFIER SPECIFICATIONS

MODEL NO:

S-4000

S-5000

S-6000

R.M.S. Output Power 2 Ch Driven
2 ohms / 4 ohms / 8 ohms,
1 KHz 1% THD

2ohms 1400W
4ohms 1200W
8ohms 700W

2ohms 1800W
4ohms 1600W
8ohms 900W

2ohms 2600W
4ohms 2200W
8ohms 1250W

R.M.S. Output Power Bridged Mono
4 ohms / 8 ohms,
1 KHz 1% THD

2800W/2400W

3600W/3200W

5200W/4400W

Input Sensitivity and Impedance
@ rated output power, 8 ohms

selectable (0.775V, 1V and 1.44V)

Frequency Response
20Hz-20KHz, @ rated
output power, 8 ohms

1dB

Total Harmonic Distortion
20Hz-20KHz, @ rated
output power, 8 ohms

< 0.02%

Crosstalk @ 1KHz

> 70dB

Damping Factor

> 400

Signal To Noise Ratio
below rated output power
20Hz to 20KHz, A-Weighted

> 80 dB

Power Consumption:
@rated output power, 8 ohms

12.54A @ 110V

17.45A @ 110V

24.36A @ 110V

Output Circuitry

CLASS AB

CLASS H

Cooling System:

Dual 2 - Speed Fan and Heatsinks

Dimensions
Height x Width x Depth

5.25" (13.3cm) x

19" (48.3cm) x

18.3" (46.5cm)

5.25" (13.3cm) x

19" (48.3cm) x

18.3" (46.5cm)

5.25" (13.3cm) x

19" (48.3cm) x

18.3" (46.5cm)

Weight

34.32 lbs. (15.6kg)

37.84 lbs. (17.2kg)

42.9 lbs. (19.2kg)

Rack Space

Introduction

Specifications

Front Panel Rear Panel Set Up Speakon Assembly Operating Modes Protection Features

Summary of Contents for S-4000

















Search results

Summary of Contents for S-4000

Reviews:

Related manuals for S-4000

Brands by name

Popular brands

Unika S-4000, User Instructions

Search results

Summary of Contents for S-4000

Reviews:

Related manuals for S-4000

Brands by name

Popular brands