manualshive.com logo in svg

Unika NA-3600, User Instructions, Page: 6 / 16

Share
Download
Unika NA-3600 User Instructions Download Page 6

NA-8600 REAR PANEL

page 5

18. Channel

 

1 Frequency Adj

. 

(NA-8600 only) 

- This pot adjust the frequency 

level sent to your speaker on channel 1 when using your amplifier in 
subwoofer mode.

19. Mode Selection Switch

 - This recessed, three-position switch configures 

the amplifier for Stereo, Parallel or Bridged Mode operation. Amplifiers are 
factory-configured for Stereo Mode. See section on Mode Selection for more 
information.

20. Fuse Holder

 - This holder houses the external fuse. Always replace with the 

exact same type fuse, otherwise instructed to do so by an authorized audio 
service technician.

21. Channel 2 XLR THRU Jack (NA-5600 & NA-8600 only)

 - This Jack is used 

to send a parallel signal from the channel 2 input jack to another device or 
amplifier.

22. Channel 1 XLR THRU Jack

 

(NA-5600 & NA-8600 only) 

- This Jack is used 

to send a parallel signal from the channel 1 input jack to another device or 
amplifier.

23. Channel 2 Output Jack / 5-Way Binding Post

 - Connect to your speaker’s 

input jack. Red is positive signal and Black is negative signal.

24. Channel 1 Output Jack / 5-Way Binding Post

 - Connect to your speaker’s 

input jack. Red is positive signal and Black is negative signal.

25. Ground Lift Switch

 - This switch is used to disconnect the internal ground 

signal from the amplifier chassis ground. This may reduce the buzz that is 
caused from an electrical 50Hz/60Hz cycle. 

26. AC POWER Cord

 - Plug this cable into a standard 110V or 220V wall outlet. 

Be sure that the supplied voltage in your area matches the amplifiers 
required voltage. Never plug your amplifier into a wall outlet that does not 
match the required voltage of your amplifier, serious damage may occur to 
your unit.

Figure

 

4

: 

NA

-

8600

 

Rear

 

Panel

Important Precautions     Introduction

Front Panel     

     Set Up     Operating Modes     Protection    Features    Specifications

     

Rear Panels

11

14

18

16

19

21

20

11

15

12

   CAUTION

MINIMUM LOAD IMPEDANCE
2 OHM PER CHANNEL
4 OHM BRIDGE

AC IN

-120V 60Hz

FREQUENCY

CH-2

CH-1

PARALLEL

DIP

ON

1 2 3 4

20Hz

200Hz

FREQUENCY

200Hz

20Hz

NORMAL

NORMAL

CH-1

CH-2

22

23

24

25

26

13

17

UNiKA

 NA-3600/NA-5600/NA-8600

SUB

WOOFER

SUB

WOOFER

Summary of Contents for NA-3600

















Reviews:

No comments