Unify OpenStage M3 EX Operating Instructions Manual Download | Manualshive

Page: 54 / 130

background image

Conducting calls – enhanced functions

53

Activating control relays

The service engineer can set up a maximum of 4 control relays that enable var-
ious equipment (for example, door opener) to be activated and deactivated.

It is possible to access a specific control relay. Depending on the configuration,
the control relays can be
• activated and deactivated automatically, or
• activated and deactivated automatically on the basis of a timer.

Prerequisite: The service engineer has set up at least one switch.

This function can also be called by entering the code

Activating a control relay

c

or

d

Press and hold the Talk or Speakerphone key.

Open the system menu.

> <

[

Select the menu item and confirm.



> <

[

Select the menu item and confirm.

o

Follow the user guidance system from this point onwards. Enter the required
switch code (1... 4).

a

Press the On-hook key to end the operation.

Deactivating a control relay

c

or

d

Press and hold the Talk or Speakerphone key.

Open the system menu.

> <

[

Select the menu item and confirm.



> <

[

Select the menu item and confirm.

o

Follow the user guidance system from this point onwards. Enter the required
switch code (1... 4).

a

Press the On-hook key to end the operation.

Menu

Service?

*

90=Control Relay

On?

Menu

Service?

#90=Control Relay
Off?

«
...
52
53
54
55
56
...
»

Summary of Contents for OpenStage M3 EX



































































































































Reviews:

No comments

Related manuals for OpenStage M3 EX

Brand: Haier Pages: 24

Brand: Radio Shack Pages: 2

Brand: Samsung Pages: 125

Brand: TCL Pages: 55

Brand: i-mobile Pages: 58

Brand: Hama Pages: 27

Brand: Aastra Pages: 24

Brand: Manta Pages: 28

POLYCOM VTXTM 1000

Brand: Polycom Pages: 2

Brand: Micromax Pages: 14

Brand: ZTC Pages: 168

Brand: Yuxin Pages: 42

Brand: Audiovox Pages: 52

PHONEEASY 410S gsm

Brand: Doro Pages: 140

Brand: SoftBank Pages: 2

Brand: ShoreTel Pages: 3

Brand: GENERAL MOBILE Pages: 16

UNIVERGE SV8100 DT3 SERIES

Brand: NEC Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands