4
IM-POWER PREP INTRO
Adjusting the Feet
Use a tape measure and adjust the feet to the approximate height required. Turn the
hexagon foot clockwise to shorten the height of the sink or counterclockwise to raise
the height of the sink. Final adjustment of the feet will be done after the sink is in the
installed location. Set the sink and leg assembly upright on its feet.
IMPORTANT: CHEMICAL DISPENSER AND CHEMICALS FOR THE POWER PREP INTRO
MUST BE OBTAINED FROM A SOURCE OTHER THAN UNIFIED BRANDS.
Chemical Dispenser Connection
Chemical dispenser and chemicals for the Power Prep Intro are not sold by Unified
Brands; these must be obtained through other sources. Some Power Prep Intro
units are provided with a dispensing tube located in the back splash for directing the
chemical flow into the wash sink.
The discharge tube from the chemical dispenser is pushed over the end of the tube to
secure it to the backsplash. This keeps the hose in the correct location for dispensing
chemicals into the wash sink.
Faucet Installation
Open the faucet package and locate the water connection elbows, faucet body and
escutcheon assemblies. Apply Teflon tape to the threads of the elbows and insert
them though the backsplash of the sink.
Loosely fit the escutcheons to the elbows and the faucet body. When the alignment
of the body with the sink is confirmed, tighten the escutcheons onto the elbows and
faucet body. From the back side of the backsplash, tighten the brass nuts on the
elbows when the faucet body is parallel with the rim of the sink.
Complete the faucet assembly according to the manufacturer’s instructions which
are included with the faucet. Attach water lines to the faucet so that the lines extend
below the sink. This will make the plumbing easier to complete when the machine is
placed against the wall.
COMPLETING THE INSTALLATION
IMPORTANT: THE POWER PREP INTRO SINK ASSEMBLY MUST BE LEVEL FROM SIDE TO
SIDE AND FRONT TO REAR WITH ALL THE FEET MAKING FIRM CONTACT
WITH THE FLOOR.
FINAL INSTALLATION STEPS
Machine Placement
Position the Power Prep Intro so that the back splash rests against the wall and is
placed according to the floor plan or customer’s selected location. Examine the drain
and water supply lines to determine that the plumbing can be completed when the
Power Prep Intro is in the final location. Verify that the plumbing from the faucet can
be reached with the sink against the wall.
Downturned-Backsplash (“Z-Clip” Installation)
If the Power Prep Intro has an upturned backsplash, skip this
step.
If the Power Prep Intro has a backsplash that is downturned,
it will be necessary to attach the provided Z-Clips to the wall.
Using a level, adjust the feet on the Power Prep Intro until the
front rim and the rear rim of the sink are level. The sink must
also be level front to back. Measure from the floor to the top
edge of the backsplash, and then move the sink away from the wall. Locate the
Z-Clips by marking a level line on the wall approximately 3/32” below the height of
the backsplash top edge. Locate the wall studs and mark the locations. Align top
edge of Z-Clips to the marked line and securely fasten the Z-Clips to the wall, using
fasteners provided. Install screws directly to the wall’s studs whenever possible. The
Z-Clips should be spaced as evenly as possible. Move the sink to the wall and lift the
back edge over the Z-Clips.
Upturned-Backsplash
If the Power Prep Intro has a downturned backsplash, skip this
step.
Using a level, adjust the feet on the Power Prep Intro until the
front rim and the rear rim of the sink are level. The sink must
also be level front to back. Locate the wall studs and mark
their location on the top edge of the back splash. Measure
down ¾” from the top of the backsplash and then drill ¼”
diameter holes through the back splash in line with the center of the studs. Use the
included #10 stainless steel screws to attach the Power Prep Intro directly to the wall.
Seal around the Backsplash and Screws
Examine the installation to see that the wall and backsplash are clean and free of dust
and oils. Seal the top and sides of the backsplash to the wall using the clear NSF
approved sealant provided with the Power Prep Intro. Seal around the screw heads
to be sure they do not allow water to leak behind the backsplash. Wipe off all excess
sealant leaving a smooth, clean and sanitary bead of sealant on all the edges.
Rinse Riser and Anchor Installation
Follow the faucet manufacturer’s directions on the assembly of the faucet and riser.
Anchor the riser supports to the wall using the flange plate provided with the riser
assembly. It may be necessary to cut the support rods to a shorter length in order to
fit between the wall and the riser.
