background image

Warranty

13

UHF CB Transceiver

UNIDEN UH064SX-2NB

UNIDEN UH064SX-2NB UHF CB Transceiver

IMPORTANT: Satisfactory evidence of the original purchase is 

required for warranty service

Please refer to our Uniden website for any details or warranty durations 

offered in addition to those contained below.

Warrantor:

 The warrantor is either Uniden Australia Pty Limited ABN 58 

001 865 498 (“Uniden Aust”) or Uniden New Zealand Limited (“Uniden 

NZ”) as the case may be.

Terms of Warranty: 

Uniden Aust/NZ warrants to the original retail 

purchaser only that the UH064SX-2NB (“the Product”), will be free from 

defects in materials and craftsmanship for the duration of the warranty 

period, subject to the limitations and exclusions set out below.

Warranty period: 

This warranty to the original retail purchaser is only valid 

in the original country of purchase for a Product first purchased either in 

Australia or New Zealand and will expire one (1) year from the date of the 

original retail sale.
If a warranty claim is made, this warranty will not apply if the Product is 

found by Uniden to be:  
(A)  Damaged or not maintained in a reasonable manner or as 

    recommended in the relevant Uniden Owner’s Manual;

(B)  Modified, altered or used as part of any conversion kits, 

    subassemblies or any configurations not sold by Uniden Aust or 

    Uniden NZ;

(C)  Improperly installed contrary to instructions contained in the relevant 

    Owner’s Manual

(D)  Repaired by someone other than an authorized Uniden Repair Agent 

    in relation to a defect or malfunction covered by this warranty; or

(E)  Used in conjunction with any equipment, parts or a system not 

    manufactured by Uniden. 

Parts Covered:

 This warranty covers the Product and included accessories.

User-generated Data: 

This warranty does not cover any claimed loss of 

or damage to user-generated data (including but without limitation phone 

numbers, addresses and images) that may be stored on your Product.

Summary of Contents for UH064SX-2NB

















Reviews: